Data Quality Reports for Session: 117629 User: lkberg Completed: 02/18/2009

TABLE OF CONTENTS

DQR IDSubjectData Streams Affected
D040526.16SGP/RWP/I1/I2/I3 - Metadata errorssgp915rwptempconI1.a1, sgp915rwptempconI2.a1, sgp915rwptempconI3.a1, sgp915rwptempmomI1.a0,
sgp915rwptempmomI2.a0, sgp915rwptempmomI3.a0, sgp915rwptempspecI1.a0,
sgp915rwptempspecI2.a0, sgp915rwptempspecI3.a0, sgp915rwpwindconI1.a1, sgp915rwpwindconI2.a1,
sgp915rwpwindconI3.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindmomI2.a0, sgp915rwpwindmomI3.a0,
sgp915rwpwindspecI1.a0, sgp915rwpwindspecI2.a0, sgp915rwpwindspecI3.a0
D050110.2SGP/RWP/I3 - Missing datasgp915rwpI3.00, sgp915rwprawI3.00, sgp915rwptempconI3.a1, sgp915rwptempmomI3.a0,
sgp915rwptempspecI3.a0, sgp915rwpwindconI3.a1, sgp915rwpwindmomI3.a0, sgp915rwpwindspecI3.a0
D060517.1SGP/RWP/I1 - Wind speed too small, directions likely bad due to incorrect beam controlsgp915rwpwindconI1.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindspecI1.a0
D090129.3SGP/RWP/I1 - Instrument down for final amplifier maintenance: ref dqpr 2043sgp915rwptempconI1.a1, sgp915rwptempmomI1.a0, sgp915rwptempspecI1.a0,
sgp915rwpwindconI1.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindspecI1.a0


DQRID : D040526.16
Start DateStart TimeEnd DateEnd Time
04/01/2001000005/07/20032359
Subject:
SGP/RWP/I1/I2/I3 - Metadata errors
DataStreams:sgp915rwptempconI1.a1, sgp915rwptempconI2.a1, sgp915rwptempconI3.a1, sgp915rwptempmomI1.a0,
sgp915rwptempmomI2.a0, sgp915rwptempmomI3.a0, sgp915rwptempspecI1.a0,
sgp915rwptempspecI2.a0, sgp915rwptempspecI3.a0, sgp915rwpwindconI1.a1, sgp915rwpwindconI2.a1,
sgp915rwpwindconI3.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindmomI2.a0, sgp915rwpwindmomI3.a0,
sgp915rwpwindspecI1.a0, sgp915rwpwindspecI2.a0, sgp915rwpwindspecI3.a0
Description:
The latitude, longitude and altitude of the Intermediate Facility
915RWPs were incorrectly entered into the ARM database.

The correct location of the SGP.I1 915RWP is:
   Lat: 37.626N
   Lon: 96.538W
   Alt:    478m

The correct location of the SGP.I2 915RWP is:
   Lat: 37.280N
   Lon: 98.933W
   Alt:    616m

The correct location of the SGP.I3 915RWP is:
   Lat: 35.551N
   Lon: 96.864W
   Alt:    275m
Measurements:sgp915rwptempmomI1.a0:
  • lon(lon)
  • Dummy altitude for Zeb(alt)
  • lat(lat)
sgp915rwpwindconI2.a1:
  • lon(lon)
  • lat(lat)
  • Dummy altitude for Zeb(alt)
sgp915rwpwindmomI3.a0:
  • lat(lat)
  • Dummy altitude for Zeb(alt)
  • lon(lon)
sgp915rwpwindspecI2.a0:
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • lon(lon)
sgp915rwpwindconI1.a1:
  • lon(lon)
  • lat(lat)
  • Dummy altitude for Zeb(alt)
sgp915rwpwindmomI2.a0:
  • lat(lat)
  • lon(lon)
  • Dummy altitude for Zeb(alt)
sgp915rwptempspecI3.a0:
  • lon(lon)
  • Dummy altitude for Zeb(alt)
  • lat(lat)
sgp915rwptempspecI2.a0:
  • lon(lon)
  • lat(lat)
  • Dummy altitude for Zeb(alt)
sgp915rwptempconI1.a1:
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • lon(lon)
sgp915rwptempmomI3.a0:
  • lat(lat)
  • lon(lon)
  • Dummy altitude for Zeb(alt)
sgp915rwptempspecI1.a0:
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • lon(lon)
sgp915rwpwindmomI1.a0:
  • Dummy altitude for Zeb(alt)
  • lon(lon)
  • lat(lat)
sgp915rwpwindspecI3.a0:
  • lat(lat)
  • lon(lon)
  • Dummy altitude for Zeb(alt)
sgp915rwptempconI3.a1:
  • lon(lon)
  • lat(lat)
  • Dummy altitude for Zeb(alt)
sgp915rwpwindconI3.a1:
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • lon(lon)
sgp915rwpwindspecI1.a0:
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • lon(lon)
sgp915rwptempmomI2.a0:
  • lon(lon)
  • Dummy altitude for Zeb(alt)
  • lat(lat)
sgp915rwptempconI2.a1:
  • Dummy altitude for Zeb(alt)
  • lon(lon)
  • lat(lat)

Back To Table of Contents

DQRID : D050110.2
Start DateStart TimeEnd DateEnd Time
09/01/2004000003/01/20052359
03/31/2005000005/29/20052359
06/07/2006000009/27/20062359
Subject:
SGP/RWP/I3 - Missing data
DataStreams:sgp915rwpI3.00, sgp915rwprawI3.00, sgp915rwptempconI3.a1, sgp915rwptempmomI3.a0,
sgp915rwptempspecI3.a0, sgp915rwpwindconI3.a1, sgp915rwpwindmomI3.a0, sgp915rwpwindspecI3.a0
Description:
The phase shifter at Meeker failed and repeated efforts to repair it failed. There may be 
a few dates within the specified missing data range where data exists but it was part of 
a trouble shooting exercise and should be ignored.
Measurements:sgp915rwpI3.00:
  • null(Raw data stream - documentation not supported)
sgp915rwpwindmomI3.a0:
  • 1000 * log10(noise signal level: vert vel)(noise)
  • Mean atmospheric vertical velocity(mdf)
sgp915rwprawI3.00:
  • Raw data stream - documentation not supported(raw)
sgp915rwpwindspecI3.a0:
  • Spectral Data (signal strength/freq int)(spc_amp)
sgp915rwptempconI3.a1:
  • virtual_temp_corr(virtual_temp_corr)
  • Time offset of tweaks from base_time(time_offset)
  • Number of Values that Passed Consensus, Beam 0 Virtual Temperature(ncns_virtual_temp)
  • Signal to Noise Ratio, Corrected Beam 0 Virtual Temperature(snr_virtual_temp_corr)
  • Number of Values that Passed Consensus, Corrected Beam 0 Virtual Temperature(ncns_virtual_temp_corr)
  • Number of Values Required for Consensus, Beam 0(nrcns)
  • Beam 0 virtual temperature(virtual_temp)
  • Signal to Noise Ratio, Beam 0 Virtual Temperature(snr_virtual_temp)
  • Vertical wind velocity(vert_v)
  • Number of pulses/ave int, Beam 0(nrec)
  • Number of Values that Passed Consensus, Vertical wind velocity(ncns_vert_v)
  • Signal to Noise Ratio, Vertical wind velocity(snr_vert_v)
sgp915rwpwindconI3.a1:
  • Number of Values Required for Consensus, Beam 1(nrcns1)
  • Number of values that passed consensus, beam 4(ncns4)
  • Number of spectra/ave int, Beam 2(nrec2)
  • Number of Values Required for Consensus, Beam 3(nrcns3)
  • Beam 1 radial wind speed(vel1)
  • Beam 2 radial wind speed(vel2)
  • Number of values that passed consensus, beam 1(ncns1)
  • Ave snr*10 level, Beam 2(snr2)
  • Number of values that passed consensus, beam 3(ncns3)
  • Number of Values Required for Consensus, Beam 2(nrcns2)
  • Number of Values Required for Consensus, Beam 4(nrcns4)
  • Number of values that passed consensus, beam 2(ncns2)
  • copolar signal to noise ratio(snr1)
  • U-component(u_wind)
  • Number of values that passed consensus, beam 0(ncns0)
  • Beam 4 radial wind speed(vel4)
  • Number of Values Required for Consensus, Beam 0(nrcns0)
  • Signal to Noise Ratio, Beam 4(snr4)
  • Signal to Noise Ratio, Beam 3(snr3)
  • Beam 3 radial wind speed(vel3)
  • Number of spectra/ave int, Beam 0(nrec0)
  • Beam 0 radial wind speed(vel0)
  • Number of spectra/ave int, Beam 1(nrec1)
  • Signal to Noise Ratio, Beam 0(snr0)
  • Number of spectra/ave int, Beam 4(nrec4)
  • V-component(v_wind)
  • Number of spectra/ave int, Beam 3(nrec3)
sgp915rwptempspecI3.a0:
  • Spectral Data (signal strength/freq int)(spc_amp)
sgp915rwptempmomI3.a0:
  • Beam 0 virtual temperature(virtual_temp)
  • Signal to Noise Ratio of the RASS Signal(snr)
  • Signal to Noise Ratio: acoustic(ssnr)
  • Mean atmospheric vertical velocity(mdf)
  • 1000 * log10(noise signal level: vert vel)(noise)
  • Range Gate Spacing(rgs)
  • Acoustic Spectral Width(sspecw)
  • Mean acoustic speed(smdf)
  • Spectral Width: vert velocity(specw)

Back To Table of Contents

DQRID : D060517.1
Start DateStart TimeEnd DateEnd Time
07/21/2005152804/11/20061112
Subject:
SGP/RWP/I1 - Wind speed too small, directions likely bad due to incorrect beam control
DataStreams:sgp915rwpwindconI1.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindspecI1.a0
Description:
two beams, sometimes three of the four tilted possible are incorrect due either to a phase 
shifter problem or improper control of the phase shifter.
Measurements:sgp915rwpwindmomI1.a0:
  • Mean atmospheric vertical velocity(mdf)
sgp915rwpwindspecI1.a0:
  • Spectral Data (signal strength/freq int)(spc_amp)
sgp915rwpwindconI1.a1:
  • V-component(v_wind)
  • Beam 2 radial wind speed(vel2)
  • U-component(u_wind)
  • Beam 4 radial wind speed(vel4)
  • Beam 1 radial wind speed(vel1)
  • Beam 3 radial wind speed(vel3)

Back To Table of Contents

DQRID : D090129.3
Start DateStart TimeEnd DateEnd Time
11/13/2008150012/08/20081500
Subject:
SGP/RWP/I1 - Instrument down for final amplifier maintenance: ref dqpr 2043
DataStreams:sgp915rwptempconI1.a1, sgp915rwptempmomI1.a0, sgp915rwptempspecI1.a0,
sgp915rwpwindconI1.a1, sgp915rwpwindmomI1.a0, sgp915rwpwindspecI1.a0
Description:
Final amplifier ceased transmitting.  Was removed from service on 11/13 and repaired at 
CF. Replaced power supply and returned to service on 12/08
Measurements:sgp915rwpwindmomI1.a0:
  • Spectral Width: vert velocity(specw)
  • Ave Time per Average Spectra. Also known as dwell.(spcavetime)
  • Vertical FFT Bandwidth(vband)
  • Delay Time to 1st Gate(dly)
  • Pulse Length(plen)
  • Sample Rate(sampr)
  • Radial Velocity Spectral Resolution(vsr)
  • Number of Pulse Code Bits(pcbits)
  • lon(lon)
  • 1000 * log10(noise signal level: vert vel)(noise)
  • Range Gate Spacing(rgs)
  • Interpulse Period(ipp)
  • Pulse Repetition Frequency(prf)
  • lat(lat)
  • Individual Spectrum Integration Time(sitime)
  • Number of valid heights(nheight)
  • Number of Coherent Samples/spectral point(ncoh)
  • Height of Center of First Range Gate(rgf)
  • Rx Bandwidth Switch Code(bswitch)
  • Array of heights for each sample time(height_t)
  • Dummy altitude for Zeb(alt)
  • Beam Number(beam)
  • Number of Individual Spectra/Average Spectrum(nspc)
  • base time(base_time)
  • Mean atmospheric vertical velocity(mdf)
  • Signal to Noise Ratio of the RASS Signal(snr)
  • Height of Center of Last Range Gate(rgl)
  • Height Index(range_gate)
  • Oblique FFT Bandwidth(oband)
  • Time Domain Integration Time(tditime)
  • Time offset of tweaks from base_time(time_offset)
  • elevation(elevation)
sgp915rwptempmomI1.a0:
  • Signal to Noise Ratio of the RASS Signal(snr)
  • lon(lon)
  • Acoustic Spectral Width(sspecw)
  • Time offset of tweaks from base_time(time_offset)
  • Dummy altitude for Zeb(alt)
  • Range Gate Spacing(rgs)
  • base time(base_time)
  • Mean acoustic speed(smdf)
  • Beam 0 virtual temperature(virtual_temp)
  • Sample Rate(sampr)
  • 1000 * log10(noise signal level: vert vel)(noise)
  • Mean atmospheric vertical velocity(mdf)
  • Spectral Width: vert velocity(specw)
  • Array of heights for the range gates(height)
  • Signal to Noise Ratio: acoustic(ssnr)
  • lat(lat)
sgp915rwpwindspecI1.a0:
  • Particle radius at logarithmic center of bin(bins)
  • elevation(elevation)
  • Time Domain Integration Time(tditime)
  • Dummy altitude for Zeb(alt)
  • Pulse Repetition Frequency(prf)
  • base time(base_time)
  • Spectral Data (signal strength/freq int)(spc_amp)
  • Height of Center of First Range Gate(rgf)
  • Number of Pulse Code Bits(pcbits)
  • lat(lat)
  • Number of Coherent Samples/spectral point(ncoh)
  • Delay Time to 1st Gate(dly)
  • Sample Rate(sampr)
  • Number of valid heights(nheight)
  • Rx Bandwidth Switch Code(bswitch)
  • Individual Spectrum Integration Time(sitime)
  • Oblique FFT Bandwidth(oband)
  • Height Index(range_gate)
  • Radial Velocity Spectral Resolution(vsr)
  • Range Gate Spacing(rgs)
  • Number of Individual Spectra/Average Spectrum(nspc)
  • Pulse Length(plen)
  • Array of heights for each sample time(height_t)
  • Height of Center of Last Range Gate(rgl)
  • lon(lon)
  • Time offset of tweaks from base_time(time_offset)
  • Ave Time per Average Spectra.(spcavetim)
  • Beam Number(beam)
  • Vertical FFT Bandwidth(vband)
  • Interpulse Period(ipp)
sgp915rwpwindconI1.a1:
  • Time Domain Integration Time(tditime)
  • Number of values that passed consensus, beam 4(ncns4)
  • Height Index(range_gate)
  • Beam 1 radial wind speed(vel1)
  • Horizontal wind direction(dir)
  • Number of values that passed consensus, beam 0(ncns0)
  • Number of values that passed consensus, beam 1(ncns1)
  • lon(lon)
  • Number of spectra/ave int, Beam 2(nrec2)
  • Pulse Repetition Frequency(prf)
  • Beam 0 radial wind speed(vel0)
  • Vertical Velocity Spectral Resolution(vvsr)
  • Azimuth of Beam 1(azimuth1)
  • Elevation angle of Beam 0 for WINDS data(elevation0)
  • Horizontal wind speed(spd)
  • Elevation angle of Beam 3 for WINDS data(elevation3)
  • Ave Time per Average Spectra.(spcavetim)
  • Number of values that passed consensus, beam 2(ncns2)
  • Dummy altitude for Zeb(alt)
  • Number of Values Required for Consensus, Beam 1(nrcns1)
  • Range Gate Spacing(rgs)
  • Elevation angle of Beam 2 for WINDS data(elevation2)
  • Interpulse Period(ipp)
  • Beam 4 radial wind speed(vel4)
  • Number of values that passed consensus, beam 3(ncns3)
  • Delay Time to 1st Gate(dly)
  • Array of heights for each sample time(height_p)
  • Elevation angle of Beam 1 for WINDS data(elevation1)
  • Rx Bandwidth Switch Code(bswitch)
  • Sample Rate(sampr)
  • copolar signal to noise ratio(snr1)
  • Height of Center of First Range Gate(rgf)
  • U-component(u_wind)
  • Number of Individual Spectra/Average Spectrum(nspc)
  • Number of Values Required for Consensus, Beam 2(nrcns2)
  • Vertical FFT Bandwidth(vband)
  • Signal to Noise Ratio, Beam 0(snr0)
  • Number of Pulse Code Bits(pcbits)
  • Number of Values Required for Consensus, Beam 0(nrcns0)
  • Azimuth of Beam 2(azimuth2)
  • Elevation angle of Beam 4 for WINDS data(elevation4)
  • Number of Values Required for Consensus, Beam 3(nrcns3)
  • Azimuth of Beam 3 for WINDS data(azimuth3)
  • Pulse Length(plen)
  • lat(lat)
  • Oblique Velocity Spectral Resolution(ovsr)
  • Azimuth of Beam 4 for WINDS data(azimuth4)
  • Number of Values Required for Consensus, Beam 4(nrcns4)
  • V-component(v_wind)
  • Number of Coherent Samples/spectral point(ncoh)
  • Signal to Noise Ratio, Beam 3(snr3)
  • Beam 2 radial wind speed(vel2)
  • Oblique FFT Bandwidth(oband)
  • Average Interval(avgint)
  • Beam 3 radial wind speed(vel3)
  • Azimuth of Beam 0(azimuth0)
  • base time(base_time)
  • Height of Center of Last Range Gate(rgl)
  • Number of spectra/ave int, Beam 4(nrec4)
  • Time offset of tweaks from base_time(time_offset)
  • Ave snr*10 level, Beam 2(snr2)
  • Number of spectra/ave int, Beam 1(nrec1)
  • Signal to Noise Ratio, Beam 4(snr4)
  • Individual Spectrum Integration Time(sitime)
  • Number of spectra/ave int, Beam 3(nrec3)
  • Power offset(power)
  • Number of spectra/ave int, Beam 0(nrec0)
  • Number of valid heights(nheight)
sgp915rwptempconI1.a1:
  • Time offset of tweaks from base_time(time_offset)
  • Dummy altitude for Zeb(alt)
  • lat(lat)
  • base time(base_time)
  • Number of Values that Passed Consensus, Beam 0 Virtual Temperature(ncns_virtual_temp)
  • Signal to Noise Ratio, Corrected Beam 0 Virtual Temperature(snr_virtual_temp_corr)
  • lon(lon)
  • Range Gate Spacing(rgs)
  • Vertical wind velocity(vert_v)
  • Array of heights for the range gates(height)
  • Number of pulses/ave int, Beam 0(nrec)
  • Average Interval(avgint)
  • Sample Rate(sampr)
  • Number of Values Required for Consensus, Beam 0(nrcns)
  • Signal to Noise Ratio, Beam 0 Virtual Temperature(snr_virtual_temp)
  • Beam 0 virtual temperature(virtual_temp)
  • Signal to Noise Ratio, Vertical wind velocity(snr_vert_v)
  • virtual_temp_corr(virtual_temp_corr)
  • Number of Values that Passed Consensus, Corrected Beam 0 Virtual Temperature(ncns_virtual_temp_corr)
  • Number of Values that Passed Consensus, Vertical wind velocity(ncns_vert_v)
sgp915rwptempspecI1.a0:
  • base time(base_time)
  • lat(lat)
  • Particle radius at logarithmic center of bin(bins)
  • Spectral Data (signal strength/freq int)(spc_amp)
  • Dummy altitude for Zeb(alt)
  • Array of heights for the range gates(height)
  • Sample Rate(sampr)
  • Range Gate Spacing(rgs)
  • Time offset of tweaks from base_time(time_offset)
  • lon(lon)

Back To Table of Contents


END OF DATA