| Measurements: | awrkasacrawrhiauxM1.a0: - Positioner elevation velocity(elevation_scan_rate)
- Coolant supply temperature(temp_coolant_supply)
- Modulator interlock status(interlock_status)
- Beam Elevation Angle(elevation)
- Modulator filament status(fil_delay)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Modulator body current(voltage_body_current)
- Humidity measured by sensor on radar control board(local_humidity)
- Azimuth of Radar Ray(azimuth)
- Voltage of 28V power supply(power_supply_28v)
- Coolant return temperature(temp_coolant_return)
- User azimuth cycle count(user_azimuth_cycle_count)
- Sweep counter in azimuth(azimuth_sweep_count)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Modulator high voltage on(hv_on)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Noise figure cross-polar(noise_figure_xpol)
- User elevation cycle count(user_elevation_cycle_count)
- Humidity measured by probe inside antenna(remote_humidity)
- Voltage of 5V power supply(power_supply_5v)
- Cold power, copolar(cold_power_copol)
- Description of current scanning mode(pacsi_call_stack)
- Antenna power(antenna_power)
- Voltage of 8V power supply(power_supply_8v)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Cold power, cross-polar(cold_power_xpol)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Hot power, copolar(hot_power_copol)
- Sweep counter in elevation(elevation_sweep_count)
- DC power supply temperature(temp_dc_power_supply)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Voltage of 12V power supply(power_supply_12v)
- Positioner azimuth motor current(az_motor_current)
- Voltage of -5V power supply(power_supply_minus5v)
- Receiver gain cross-polar(receiver_gain_xpol)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Voltage of 15V power supply(power_supply_15v)
- Noise figure copolar(noise_figure_copol)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Receiver gain copolar(receiver_gain_copol)
- Time offset from base_time(time_offset)
- time_in_seconds_since_volume_start(time)
- base time in epoch(base_time)
- Drive power(drive_power)
- Fault summary(fault_sum)
- Temperature measured by probe inside antenna(remote_temp)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Positioner azimuth velocity(azimuth_scan_rate)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Output power(output_power)
- data_volume_index_number(volume_number)
- Modulator temperature(temp_modulator)
- Synchronization fault status(sync_fault)
- Modulator fault status(modulator_fault)
- Temperature measured by sensor on radar control board(local_temp)
- Hot power, cross-polar(hot_power_xpol)
- IF unit temperature(temp_if_unit)
- EIKA temperature(temp_eika)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Modulator collector current(voltage_modulator_collector_current)
- Power validity status(power_valid)
- lon(lon)
- Transmitter fault status(transmitter_temp_fault)
- Positioner elevation motor current(el_motor_current)
more
awrkasacrzppiM1.a1: - base time in epoch(base_time)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- Sweep number, zero-based count(sweep_number)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Primary axis of rotation(primary_axis)
- Pulse width for this calibration(r_calib_pulse_width)
- altitude_above_ground_level(altitude_agl)
- Radar beam width, vertical channel(radar_beam_width_v)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- reflectivity(reflectivity)
- Sky noise, cross-polarization(sky_noise_xpol)
- Scan mode for sweep(sweep_mode)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- type_of_instrument(instrument_type)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- ray_target_fixed_angle(fixed_angle)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Time of the calibration that applies to each ray(r_calib_time)
- platform_type(platform_type)
- Signal-to-noise-ratio(snr)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- Pulse width(pulse_width)
- East longitude(longitude)
- Unambiguous Doppler velocity(nyquist_velocity)
- Sky power, copolar(sky_power_copol)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Unambiguous range(unambiguous_range)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- North latitude(latitude)
- time_in_seconds_since_volume_start(time)
- Mean doppler velocity(mean_doppler_velocity)
- Polarization mode(polarization_mode)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- Follow mode(follow_mode)
- radiation_frequency(frequency)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Number of samples used to compute moments(n_samples)
- Time corresponding to last radial in file(time_coverage_end)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- pulse_repetition_frequency(prt)
- Linear depolarization ratio(linear_depolarization_ratio)
- Azimuth of Radar Ray(azimuth)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- data_volume_index_number(volume_number)
- Index for the calibration that applies to each ray(r_calib_index)
- data_volume_start_time_utc(time_coverage_start)
- lon(lon)
- altitude(altitude)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Sky noise, copolar(sky_noise_copol)
- Transmit power(r_calib_xmit_power_h)
- transmit_pulse_mode(prt_mode)
- Sky power, cross-polar(sky_power_xpol)
- Beam Elevation Angle(elevation)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- Time offset from base_time(time_offset)
- Distance to the center of the corresponding range bin(range)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
more
awrkasacrslrM1.a1: - North latitude(latitude)
- Time offset from base_time(time_offset)
- Scan mode for sweep(sweep_mode)
- Sky power, copolar(sky_power_copol)
- Signal-to-noise-ratio(snr)
- transmit_pulse_mode(prt_mode)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- data_volume_start_time_utc(time_coverage_start)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- platform_type(platform_type)
- Sweep number, zero-based count(sweep_number)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Primary axis of rotation(primary_axis)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- base time in epoch(base_time)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- Radar beam width, vertical channel(radar_beam_width_v)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- reflectivity(reflectivity)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Sky noise, cross-polarization(sky_noise_xpol)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Number of samples used to compute moments(n_samples)
- Sky power, cross-polar(sky_power_xpol)
- ray_target_fixed_angle(fixed_angle)
- Pulse width(pulse_width)
- Unambiguous range(unambiguous_range)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- lon(lon)
- Polarization mode(polarization_mode)
- Time of the calibration that applies to each ray(r_calib_time)
- Sky noise, copolar(sky_noise_copol)
- altitude(altitude)
- pulse_repetition_frequency(prt)
- Azimuth of Radar Ray(azimuth)
- Mean doppler velocity(mean_doppler_velocity)
- radiation_frequency(frequency)
- Follow mode(follow_mode)
- East longitude(longitude)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Distance to the center of the corresponding range bin(range)
- Pulse width for this calibration(r_calib_pulse_width)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- time_in_seconds_since_volume_start(time)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Index for the calibration that applies to each ray(r_calib_index)
- Linear depolarization ratio(linear_depolarization_ratio)
- data_volume_index_number(volume_number)
- Time corresponding to last radial in file(time_coverage_end)
- altitude_above_ground_level(altitude_agl)
- Transmit power(r_calib_xmit_power_h)
- type_of_instrument(instrument_type)
- Beam Elevation Angle(elevation)
- Unambiguous Doppler velocity(nyquist_velocity)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
more
awrkasacrppiauxM1.a0: - Humidity measured by sensor on radar control board(local_humidity)
- Cold power, cross-polar(cold_power_xpol)
- Voltage of 8V power supply(power_supply_8v)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Receiver gain copolar(receiver_gain_copol)
- Modulator collector current(voltage_modulator_collector_current)
- Voltage of 5V power supply(power_supply_5v)
- Transmit pulse is enabled(transmit_pulse_enabled)
- base time in epoch(base_time)
- Azimuth of Radar Ray(azimuth)
- Power validity status(power_valid)
- Voltage of 12V power supply(power_supply_12v)
- Sweep counter in elevation(elevation_sweep_count)
- Description of current scanning mode(pacsi_call_stack)
- Coolant return temperature(temp_coolant_return)
- Positioner azimuth velocity(azimuth_scan_rate)
- Voltage of 15V power supply(power_supply_15v)
- Modulator temperature(temp_modulator)
- Noise figure cross-polar(noise_figure_xpol)
- Modulator fault status(modulator_fault)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- DC power supply temperature(temp_dc_power_supply)
- IF unit temperature(temp_if_unit)
- Transmitter fault status(transmitter_temp_fault)
- Output power(output_power)
- Modulator high voltage on(hv_on)
- Positioner elevation motor current(el_motor_current)
- Voltage of -5V power supply(power_supply_minus5v)
- Drive power(drive_power)
- Fault summary(fault_sum)
- lon(lon)
- Time offset from base_time(time_offset)
- Receiver gain cross-polar(receiver_gain_xpol)
- User elevation cycle count(user_elevation_cycle_count)
- Noise figure copolar(noise_figure_copol)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Modulator body current(voltage_body_current)
- Synchronization fault status(sync_fault)
- Sweep counter in azimuth(azimuth_sweep_count)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Antenna power(antenna_power)
- North Latitude(lat)
- Voltage of 28V power supply(power_supply_28v)
- -180.0 - +180.0(alt)
- Modulator interlock status(interlock_status)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- EIKA temperature(temp_eika)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- data_volume_index_number(volume_number)
- Cold power, copolar(cold_power_copol)
- Hot power, copolar(hot_power_copol)
- Modulator filament status(fil_delay)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- time_in_seconds_since_volume_start(time)
- Beam Elevation Angle(elevation)
- User azimuth cycle count(user_azimuth_cycle_count)
- Hot power, cross-polar(hot_power_xpol)
- Coolant supply temperature(temp_coolant_supply)
- Positioner elevation velocity(elevation_scan_rate)
- Positioner azimuth motor current(az_motor_current)
- Temperature measured by sensor on radar control board(local_temp)
- Temperature measured by probe inside antenna(remote_temp)
- Humidity measured by probe inside antenna(remote_humidity)
more
awrkasacrslrauxM1.a0: - time_in_seconds_since_volume_start(time)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Synchronization fault status(sync_fault)
- Voltage of 5V power supply(power_supply_5v)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Modulator collector current(voltage_modulator_collector_current)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Voltage of 8V power supply(power_supply_8v)
- Voltage of 12V power supply(power_supply_12v)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Cold power, cross-polar(cold_power_xpol)
- Positioner azimuth motor current(az_motor_current)
- Voltage of 15V power supply(power_supply_15v)
- Beam Elevation Angle(elevation)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Modulator fault status(modulator_fault)
- Cold power, copolar(cold_power_copol)
- User azimuth cycle count(user_azimuth_cycle_count)
- Positioner azimuth velocity(azimuth_scan_rate)
- Modulator temperature(temp_modulator)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Sweep counter in azimuth(azimuth_sweep_count)
- EIKA temperature(temp_eika)
- Azimuth of Radar Ray(azimuth)
- Time offset from base_time(time_offset)
- Positioner elevation velocity(elevation_scan_rate)
- Coolant supply temperature(temp_coolant_supply)
- Drive power(drive_power)
- Modulator body current(voltage_body_current)
- Hot power, cross-polar(hot_power_xpol)
- Noise figure copolar(noise_figure_copol)
- Humidity measured by sensor on radar control board(local_humidity)
- Hot power, copolar(hot_power_copol)
- Power validity status(power_valid)
- Antenna power(antenna_power)
- Positioner elevation motor current(el_motor_current)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Coolant return temperature(temp_coolant_return)
- Noise figure cross-polar(noise_figure_xpol)
- Humidity measured by probe inside antenna(remote_humidity)
- Temperature measured by sensor on radar control board(local_temp)
- Modulator interlock status(interlock_status)
- Voltage of 28V power supply(power_supply_28v)
- Fault summary(fault_sum)
- Sweep counter in elevation(elevation_sweep_count)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Voltage of -5V power supply(power_supply_minus5v)
- Receiver gain copolar(receiver_gain_copol)
- User elevation cycle count(user_elevation_cycle_count)
- -180.0 - +180.0(alt)
- base time in epoch(base_time)
- North Latitude(lat)
- Transmitter fault status(transmitter_temp_fault)
- Receiver gain cross-polar(receiver_gain_xpol)
- Temperature measured by probe inside antenna(remote_temp)
- Description of current scanning mode(pacsi_call_stack)
- Modulator high voltage on(hv_on)
- DC power supply temperature(temp_dc_power_supply)
- data_volume_index_number(volume_number)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Output power(output_power)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- lon(lon)
- IF unit temperature(temp_if_unit)
- Modulator filament status(fil_delay)
more
awrkasacrblrhiauxM1.a0: - Modulator interlock status(interlock_status)
- Voltage of -5V power supply(power_supply_minus5v)
- Voltage of 28V power supply(power_supply_28v)
- Hot power, cross-polar(hot_power_xpol)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- lon(lon)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- DC power supply temperature(temp_dc_power_supply)
- base time in epoch(base_time)
- Azimuth of Radar Ray(azimuth)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Noise figure copolar(noise_figure_copol)
- Power validity status(power_valid)
- Coolant return temperature(temp_coolant_return)
- EIKA temperature(temp_eika)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Beam Elevation Angle(elevation)
- Sweep counter in elevation(elevation_sweep_count)
- Coolant supply temperature(temp_coolant_supply)
- Positioner elevation velocity(elevation_scan_rate)
- Modulator filament status(fil_delay)
- Modulator fault status(modulator_fault)
- Transmitter fault status(transmitter_temp_fault)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Temperature measured by probe inside antenna(remote_temp)
- Noise figure cross-polar(noise_figure_xpol)
- Modulator high voltage on(hv_on)
- Positioner elevation motor current(el_motor_current)
- Temperature measured by sensor on radar control board(local_temp)
- Receiver gain cross-polar(receiver_gain_xpol)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- User azimuth cycle count(user_azimuth_cycle_count)
- Time offset from base_time(time_offset)
- Synchronization fault status(sync_fault)
- Voltage of 15V power supply(power_supply_15v)
- data_volume_index_number(volume_number)
- Voltage of 12V power supply(power_supply_12v)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Humidity measured by probe inside antenna(remote_humidity)
- Modulator body current(voltage_body_current)
- Modulator collector current(voltage_modulator_collector_current)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Modulator temperature(temp_modulator)
- Voltage of 8V power supply(power_supply_8v)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- IF unit temperature(temp_if_unit)
- Voltage of 5V power supply(power_supply_5v)
- time_in_seconds_since_volume_start(time)
- Description of current scanning mode(pacsi_call_stack)
- Cold power, cross-polar(cold_power_xpol)
- Cold power, copolar(cold_power_copol)
- Output power(output_power)
- Sweep counter in azimuth(azimuth_sweep_count)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- User elevation cycle count(user_elevation_cycle_count)
- Receiver gain copolar(receiver_gain_copol)
- Antenna power(antenna_power)
- Fault summary(fault_sum)
- Hot power, copolar(hot_power_copol)
- Drive power(drive_power)
- Positioner azimuth motor current(az_motor_current)
- Positioner azimuth velocity(azimuth_scan_rate)
- Humidity measured by sensor on radar control board(local_humidity)
more
awrkasacrrhiM1.a1: - Polarization mode(polarization_mode)
- Linear depolarization ratio(linear_depolarization_ratio)
- Sky power, cross-polar(sky_power_xpol)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Azimuth of Radar Ray(azimuth)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Signal-to-noise-ratio(snr)
- Mean doppler velocity(mean_doppler_velocity)
- Sweep number, zero-based count(sweep_number)
- Transmit power(r_calib_xmit_power_h)
- transmit_pulse_mode(prt_mode)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- ray_target_fixed_angle(fixed_angle)
- altitude_above_ground_level(altitude_agl)
- Primary axis of rotation(primary_axis)
- time_in_seconds_since_volume_start(time)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- North latitude(latitude)
- type_of_instrument(instrument_type)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- Beam Elevation Angle(elevation)
- data_volume_start_time_utc(time_coverage_start)
- Pulse width(pulse_width)
- Unambiguous Doppler velocity(nyquist_velocity)
- pulse_repetition_frequency(prt)
- Time corresponding to last radial in file(time_coverage_end)
- Sky noise, copolar(sky_noise_copol)
- -180.0 - +180.0(alt)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- base time in epoch(base_time)
- Follow mode(follow_mode)
- platform_type(platform_type)
- North Latitude(lat)
- altitude(altitude)
- reflectivity(reflectivity)
- Sky power, copolar(sky_power_copol)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Time of the calibration that applies to each ray(r_calib_time)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Distance to the center of the corresponding range bin(range)
- radiation_frequency(frequency)
- Radar beam width, vertical channel(radar_beam_width_v)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- Pulse width for this calibration(r_calib_pulse_width)
- data_volume_index_number(volume_number)
- Sky noise, cross-polarization(sky_noise_xpol)
- Number of samples used to compute moments(n_samples)
- Scan mode for sweep(sweep_mode)
- Time offset from base_time(time_offset)
- Index for the calibration that applies to each ray(r_calib_index)
- East longitude(longitude)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- lon(lon)
- Unambiguous range(unambiguous_range)
more
awrkasacrppiM1.a1: - time_in_seconds_since_volume_start(time)
- Time corresponding to last radial in file(time_coverage_end)
- lon(lon)
- pulse_repetition_frequency(prt)
- Sky noise, copolar(sky_noise_copol)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- North Latitude(lat)
- reflectivity(reflectivity)
- -180.0 - +180.0(alt)
- type_of_instrument(instrument_type)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- Sky noise, cross-polarization(sky_noise_xpol)
- North latitude(latitude)
- Time of the calibration that applies to each ray(r_calib_time)
- Sky power, copolar(sky_power_copol)
- Signal-to-noise-ratio(snr)
- Sky power, cross-polar(sky_power_xpol)
- Distance to the center of the corresponding range bin(range)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Radar beam width, vertical channel(radar_beam_width_v)
- Pulse width(pulse_width)
- ray_target_fixed_angle(fixed_angle)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- Beam Elevation Angle(elevation)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Transmit power(r_calib_xmit_power_h)
- data_volume_start_time_utc(time_coverage_start)
- Polarization mode(polarization_mode)
- Pulse width for this calibration(r_calib_pulse_width)
- base time in epoch(base_time)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- data_volume_index_number(volume_number)
- Sweep number, zero-based count(sweep_number)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- altitude_above_ground_level(altitude_agl)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Index for the calibration that applies to each ray(r_calib_index)
- Follow mode(follow_mode)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- radiation_frequency(frequency)
- Primary axis of rotation(primary_axis)
- Unambiguous range(unambiguous_range)
- Time offset from base_time(time_offset)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- Scan mode for sweep(sweep_mode)
- Azimuth of Radar Ray(azimuth)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- Unambiguous Doppler velocity(nyquist_velocity)
- altitude(altitude)
- Mean doppler velocity(mean_doppler_velocity)
- Number of samples used to compute moments(n_samples)
- transmit_pulse_mode(prt_mode)
- Linear depolarization ratio(linear_depolarization_ratio)
- platform_type(platform_type)
- East longitude(longitude)
more
awrkasacrcwrhiauxM1.a0: - Hot power, cross-polar(hot_power_xpol)
- Cold power, copolar(cold_power_copol)
- Modulator collector current(voltage_modulator_collector_current)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Temperature measured by sensor on radar control board(local_temp)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Modulator high voltage on(hv_on)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Sweep counter in elevation(elevation_sweep_count)
- Humidity measured by probe inside antenna(remote_humidity)
- Output power(output_power)
- Power validity status(power_valid)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Voltage of 28V power supply(power_supply_28v)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Receiver gain copolar(receiver_gain_copol)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Voltage of 15V power supply(power_supply_15v)
- Modulator interlock status(interlock_status)
- Positioner azimuth motor current(az_motor_current)
- Voltage of 12V power supply(power_supply_12v)
- User azimuth cycle count(user_azimuth_cycle_count)
- Modulator filament status(fil_delay)
- Voltage of -5V power supply(power_supply_minus5v)
- Azimuth of Radar Ray(azimuth)
- Modulator body current(voltage_body_current)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- data_volume_index_number(volume_number)
- User elevation cycle count(user_elevation_cycle_count)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Temperature measured by probe inside antenna(remote_temp)
- Beam Elevation Angle(elevation)
- North Latitude(lat)
- -180.0 - +180.0(alt)
- Positioner azimuth velocity(azimuth_scan_rate)
- Receiver gain cross-polar(receiver_gain_xpol)
- Noise figure copolar(noise_figure_copol)
- Antenna power(antenna_power)
- Synchronization fault status(sync_fault)
- IF unit temperature(temp_if_unit)
- Description of current scanning mode(pacsi_call_stack)
- lon(lon)
- Humidity measured by sensor on radar control board(local_humidity)
- Drive power(drive_power)
- Coolant return temperature(temp_coolant_return)
- base time in epoch(base_time)
- Time offset from base_time(time_offset)
- Modulator fault status(modulator_fault)
- Coolant supply temperature(temp_coolant_supply)
- Positioner elevation velocity(elevation_scan_rate)
- Voltage of 5V power supply(power_supply_5v)
- Transmitter fault status(transmitter_temp_fault)
- Voltage of 8V power supply(power_supply_8v)
- Sweep counter in azimuth(azimuth_sweep_count)
- EIKA temperature(temp_eika)
- time_in_seconds_since_volume_start(time)
- Positioner elevation motor current(el_motor_current)
- DC power supply temperature(temp_dc_power_supply)
- Cold power, cross-polar(cold_power_xpol)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Modulator temperature(temp_modulator)
- Noise figure cross-polar(noise_figure_xpol)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Fault summary(fault_sum)
- Hot power, copolar(hot_power_copol)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
more
awrkasacrawrhiM1.a1: - Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Sky noise, cross-polarization(sky_noise_xpol)
- Follow mode(follow_mode)
- Index for the calibration that applies to each ray(r_calib_index)
- Sweep number, zero-based count(sweep_number)
- Pulse width for this calibration(r_calib_pulse_width)
- Sky noise, copolar(sky_noise_copol)
- Time of the calibration that applies to each ray(r_calib_time)
- -180.0 - +180.0(alt)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- North Latitude(lat)
- lon(lon)
- radiation_frequency(frequency)
- Time corresponding to last radial in file(time_coverage_end)
- pulse_repetition_frequency(prt)
- Sky power, cross-polar(sky_power_xpol)
- Pulse width(pulse_width)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- type_of_instrument(instrument_type)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- North latitude(latitude)
- Beam Elevation Angle(elevation)
- Scan mode for sweep(sweep_mode)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- altitude(altitude)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- data_volume_index_number(volume_number)
- altitude_above_ground_level(altitude_agl)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- Time offset from base_time(time_offset)
- data_volume_start_time_utc(time_coverage_start)
- Transmit power(r_calib_xmit_power_h)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Polarization mode(polarization_mode)
- base time in epoch(base_time)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- Signal-to-noise-ratio(snr)
- Mean doppler velocity(mean_doppler_velocity)
- ray_target_fixed_angle(fixed_angle)
- time_in_seconds_since_volume_start(time)
- transmit_pulse_mode(prt_mode)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- Radar beam width, vertical channel(radar_beam_width_v)
- Linear depolarization ratio(linear_depolarization_ratio)
- Unambiguous range(unambiguous_range)
- platform_type(platform_type)
- Azimuth of Radar Ray(azimuth)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- East longitude(longitude)
- Primary axis of rotation(primary_axis)
- Distance to the center of the corresponding range bin(range)
- Unambiguous Doppler velocity(nyquist_velocity)
- Sky power, copolar(sky_power_copol)
- Number of samples used to compute moments(n_samples)
- reflectivity(reflectivity)
more
awrkasacrzppiauxM1.a0: - Modulator interlock status(interlock_status)
- DC power supply temperature(temp_dc_power_supply)
- IF unit temperature(temp_if_unit)
- Voltage of 28V power supply(power_supply_28v)
- Hot power, cross-polar(hot_power_xpol)
- Modulator fault status(modulator_fault)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Positioner azimuth velocity(azimuth_scan_rate)
- data_volume_index_number(volume_number)
- Voltage of 8V power supply(power_supply_8v)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Beam Elevation Angle(elevation)
- time_in_seconds_since_volume_start(time)
- Voltage of 5V power supply(power_supply_5v)
- Modulator filament status(fil_delay)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Positioner elevation motor current(el_motor_current)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Sweep counter in elevation(elevation_sweep_count)
- Coolant return temperature(temp_coolant_return)
- Azimuth of Radar Ray(azimuth)
- -180.0 - +180.0(alt)
- base time in epoch(base_time)
- North Latitude(lat)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Modulator collector current(voltage_modulator_collector_current)
- Modulator high voltage on(hv_on)
- Cold power, cross-polar(cold_power_xpol)
- Fault summary(fault_sum)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Temperature measured by sensor on radar control board(local_temp)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Coolant supply temperature(temp_coolant_supply)
- Positioner elevation velocity(elevation_scan_rate)
- lon(lon)
- Humidity measured by sensor on radar control board(local_humidity)
- Hot power, copolar(hot_power_copol)
- Transmitter fault status(transmitter_temp_fault)
- Humidity measured by probe inside antenna(remote_humidity)
- Noise figure copolar(noise_figure_copol)
- Receiver gain cross-polar(receiver_gain_xpol)
- Antenna power(antenna_power)
- Voltage of 15V power supply(power_supply_15v)
- Output power(output_power)
- Temperature measured by probe inside antenna(remote_temp)
- Voltage of 12V power supply(power_supply_12v)
- Synchronization fault status(sync_fault)
- Noise figure cross-polar(noise_figure_xpol)
- User azimuth cycle count(user_azimuth_cycle_count)
- User elevation cycle count(user_elevation_cycle_count)
- Modulator temperature(temp_modulator)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Modulator body current(voltage_body_current)
- Positioner azimuth motor current(az_motor_current)
- Receiver gain copolar(receiver_gain_copol)
- Power validity status(power_valid)
- Sweep counter in azimuth(azimuth_sweep_count)
- Description of current scanning mode(pacsi_call_stack)
- Cold power, copolar(cold_power_copol)
- Voltage of -5V power supply(power_supply_minus5v)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- EIKA temperature(temp_eika)
- Drive power(drive_power)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Time offset from base_time(time_offset)
more
awrkasacrhsrhiM1.a1: - radiation_frequency(frequency)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- altitude_above_ground_level(altitude_agl)
- Primary axis of rotation(primary_axis)
- East longitude(longitude)
- Pulse width(pulse_width)
- Azimuth of Radar Ray(azimuth)
- Time of the calibration that applies to each ray(r_calib_time)
- Time corresponding to last radial in file(time_coverage_end)
- Index for the calibration that applies to each ray(r_calib_index)
- North latitude(latitude)
- Sweep number, zero-based count(sweep_number)
- data_volume_index_number(volume_number)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- lon(lon)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- Transmit power(r_calib_xmit_power_h)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- pulse_repetition_frequency(prt)
- Radar beam width, vertical channel(radar_beam_width_v)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- North Latitude(lat)
- -180.0 - +180.0(alt)
- Time offset from base_time(time_offset)
- platform_type(platform_type)
- base time in epoch(base_time)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Distance to the center of the corresponding range bin(range)
- transmit_pulse_mode(prt_mode)
- reflectivity(reflectivity)
- Number of samples used to compute moments(n_samples)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Pulse width for this calibration(r_calib_pulse_width)
- type_of_instrument(instrument_type)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- altitude(altitude)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- Sky power, copolar(sky_power_copol)
- Polarization mode(polarization_mode)
- ray_target_fixed_angle(fixed_angle)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Linear depolarization ratio(linear_depolarization_ratio)
- Sky power, cross-polar(sky_power_xpol)
- Mean doppler velocity(mean_doppler_velocity)
- data_volume_start_time_utc(time_coverage_start)
- Unambiguous Doppler velocity(nyquist_velocity)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- Scan mode for sweep(sweep_mode)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Unambiguous range(unambiguous_range)
- Sky noise, copolar(sky_noise_copol)
- Signal-to-noise-ratio(snr)
- Sky noise, cross-polarization(sky_noise_xpol)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- time_in_seconds_since_volume_start(time)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Beam Elevation Angle(elevation)
- Follow mode(follow_mode)
more
awrkasacrvptauxM1.a0: - Transmitter fault status(transmitter_temp_fault)
- Antenna power(antenna_power)
- Humidity measured by probe inside antenna(remote_humidity)
- IF unit temperature(temp_if_unit)
- Modulator high voltage on(hv_on)
- Coolant return temperature(temp_coolant_return)
- Humidity measured by sensor on radar control board(local_humidity)
- Voltage of 28V power supply(power_supply_28v)
- Modulator interlock status(interlock_status)
- Receiver gain copolar(receiver_gain_copol)
- time_in_seconds_since_volume_start(time)
- Fault summary(fault_sum)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Voltage of -5V power supply(power_supply_minus5v)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Synchronization fault status(sync_fault)
- base time in epoch(base_time)
- DC power supply temperature(temp_dc_power_supply)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Modulator fault status(modulator_fault)
- lon(lon)
- Temperature measured by probe inside antenna(remote_temp)
- Noise figure cross-polar(noise_figure_xpol)
- Positioner elevation motor current(el_motor_current)
- EIKA temperature(temp_eika)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Hot power, copolar(hot_power_copol)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Voltage of 12V power supply(power_supply_12v)
- Output power(output_power)
- Voltage of 5V power supply(power_supply_5v)
- data_volume_index_number(volume_number)
- Modulator filament status(fil_delay)
- User elevation cycle count(user_elevation_cycle_count)
- Voltage of 15V power supply(power_supply_15v)
- Sweep counter in azimuth(azimuth_sweep_count)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Hot power, cross-polar(hot_power_xpol)
- Power validity status(power_valid)
- Modulator collector current(voltage_modulator_collector_current)
- Beam Elevation Angle(elevation)
- Sweep counter in elevation(elevation_sweep_count)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Noise figure copolar(noise_figure_copol)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Receiver gain cross-polar(receiver_gain_xpol)
- User azimuth cycle count(user_azimuth_cycle_count)
- Modulator body current(voltage_body_current)
- Cold power, cross-polar(cold_power_xpol)
- Positioner elevation velocity(elevation_scan_rate)
- Modulator temperature(temp_modulator)
- Description of current scanning mode(pacsi_call_stack)
- Azimuth of Radar Ray(azimuth)
- Cold power, copolar(cold_power_copol)
- Coolant supply temperature(temp_coolant_supply)
- Voltage of 8V power supply(power_supply_8v)
- Temperature measured by sensor on radar control board(local_temp)
- Time offset from base_time(time_offset)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Drive power(drive_power)
- Positioner azimuth velocity(azimuth_scan_rate)
- Positioner azimuth motor current(az_motor_current)
more
awrkasacrvptM1.a1: - data_volume_index_number(volume_number)
- Time offset from base_time(time_offset)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Beam Elevation Angle(elevation)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Distance to the center of the corresponding range bin(range)
- lon(lon)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- Pulse width for this calibration(r_calib_pulse_width)
- Number of samples used to compute moments(n_samples)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- Unambiguous Doppler velocity(nyquist_velocity)
- ray_target_fixed_angle(fixed_angle)
- altitude(altitude)
- Sky noise, cross-polarization(sky_noise_xpol)
- Azimuth of Radar Ray(azimuth)
- Transmit power(r_calib_xmit_power_h)
- North Latitude(lat)
- -180.0 - +180.0(alt)
- Unambiguous range(unambiguous_range)
- Mean doppler velocity(mean_doppler_velocity)
- transmit_pulse_mode(prt_mode)
- Sky noise, copolar(sky_noise_copol)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- base time in epoch(base_time)
- pulse_repetition_frequency(prt)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- altitude_above_ground_level(altitude_agl)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- time_in_seconds_since_volume_start(time)
- data_volume_start_time_utc(time_coverage_start)
- reflectivity(reflectivity)
- Time of the calibration that applies to each ray(r_calib_time)
- Sky power, copolar(sky_power_copol)
- Follow mode(follow_mode)
- platform_type(platform_type)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Scan mode for sweep(sweep_mode)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- radiation_frequency(frequency)
- Radar beam width, vertical channel(radar_beam_width_v)
- Linear depolarization ratio(linear_depolarization_ratio)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Polarization mode(polarization_mode)
- East longitude(longitude)
- North latitude(latitude)
- Sky power, cross-polar(sky_power_xpol)
- Signal-to-noise-ratio(snr)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Pulse width(pulse_width)
- Index for the calibration that applies to each ray(r_calib_index)
- Sweep number, zero-based count(sweep_number)
- Time corresponding to last radial in file(time_coverage_end)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- Primary axis of rotation(primary_axis)
- type_of_instrument(instrument_type)
more
awrkasacrM1.00: - (Raw data stream - documentation not supported)
more
awrkasacrblrhiM1.a1: - Radar beam width, vertical channel(radar_beam_width_v)
- Unambiguous Doppler velocity(nyquist_velocity)
- Beam Elevation Angle(elevation)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- altitude(altitude)
- pulse_repetition_frequency(prt)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- Pulse width for this calibration(r_calib_pulse_width)
- reflectivity(reflectivity)
- Polarization mode(polarization_mode)
- Mean doppler velocity(mean_doppler_velocity)
- lon(lon)
- Sky noise, copolar(sky_noise_copol)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Scan mode for sweep(sweep_mode)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- altitude_above_ground_level(altitude_agl)
- Sweep number, zero-based count(sweep_number)
- Sky noise, cross-polarization(sky_noise_xpol)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- Primary axis of rotation(primary_axis)
- type_of_instrument(instrument_type)
- Follow mode(follow_mode)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Transmit power(r_calib_xmit_power_h)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Distance to the center of the corresponding range bin(range)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- radiation_frequency(frequency)
- ray_target_fixed_angle(fixed_angle)
- East longitude(longitude)
- North latitude(latitude)
- platform_type(platform_type)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- data_volume_start_time_utc(time_coverage_start)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- Number of samples used to compute moments(n_samples)
- Pulse width(pulse_width)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Time corresponding to last radial in file(time_coverage_end)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- Signal-to-noise-ratio(snr)
- base time in epoch(base_time)
- Index for the calibration that applies to each ray(r_calib_index)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- data_volume_index_number(volume_number)
- Sky power, cross-polar(sky_power_xpol)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- Time offset from base_time(time_offset)
- Azimuth of Radar Ray(azimuth)
- Linear depolarization ratio(linear_depolarization_ratio)
- time_in_seconds_since_volume_start(time)
- Time of the calibration that applies to each ray(r_calib_time)
- Sky power, copolar(sky_power_copol)
- Unambiguous range(unambiguous_range)
- transmit_pulse_mode(prt_mode)
more
awrkasacrhsrhiauxM1.a0: - Modulator interlock status(interlock_status)
- Positioner elevation motor current(el_motor_current)
- EIKA temperature(temp_eika)
- IF unit temperature(temp_if_unit)
- Power validity status(power_valid)
- Positioner azimuth velocity(azimuth_scan_rate)
- data_volume_index_number(volume_number)
- User azimuth cycle count(user_azimuth_cycle_count)
- Modulator body current(voltage_body_current)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Transmitter fault status(transmitter_temp_fault)
- base time in epoch(base_time)
- Cold power, copolar(cold_power_copol)
- Humidity measured by probe inside antenna(remote_humidity)
- Receiver gain copolar(receiver_gain_copol)
- Fault summary(fault_sum)
- Temperature measured by sensor on radar control board(local_temp)
- Voltage of -5V power supply(power_supply_minus5v)
- Phase-locked oscillator 4 lock status(plo4_lock_status)
- Sweep counter in elevation(elevation_sweep_count)
- Time offset from base_time(time_offset)
- Drive power(drive_power)
- Hot power, copolar(hot_power_copol)
- Description of current scanning mode(pacsi_call_stack)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- Voltage of 15V power supply(power_supply_15v)
- Positioner azimuth motor current(az_motor_current)
- DC power supply temperature(temp_dc_power_supply)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Noise figure cross-polar(noise_figure_xpol)
- Modulator collector current(voltage_modulator_collector_current)
- Azimuth of Radar Ray(azimuth)
- Antenna power(antenna_power)
- North Latitude(lat)
- -180.0 - +180.0(alt)
- Voltage of 12V power supply(power_supply_12v)
- time_in_seconds_since_volume_start(time)
- Output power(output_power)
- Cold power, cross-polar(cold_power_xpol)
- Voltage of 8V power supply(power_supply_8v)
- User elevation cycle count(user_elevation_cycle_count)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Noise figure copolar(noise_figure_copol)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Voltage of 5V power supply(power_supply_5v)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Sweep counter in azimuth(azimuth_sweep_count)
- Coolant return temperature(temp_coolant_return)
- Modulator temperature(temp_modulator)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Temperature measured by probe inside antenna(remote_temp)
- Beam Elevation Angle(elevation)
- lon(lon)
- Modulator high voltage on(hv_on)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Hot power, cross-polar(hot_power_xpol)
- Modulator fault status(modulator_fault)
- Receiver gain cross-polar(receiver_gain_xpol)
- Humidity measured by sensor on radar control board(local_humidity)
- Synchronization fault status(sync_fault)
- Modulator filament status(fil_delay)
- Voltage of 28V power supply(power_supply_28v)
- Coolant supply temperature(temp_coolant_supply)
- Positioner elevation velocity(elevation_scan_rate)
more
awrkasacrspecM1.00: - (Raw data stream - documentation not supported)
more
awrkasacrrhiauxM1.a0: - Phase-locked oscillator 4 lock status(plo4_lock_status)
- lon(lon)
- Phase-locked oscillator 3 lock status(plo3_lock_status)
- Phase-locked oscillator 1 lock status(plo1_lock_status)
- Phase-locked oscillator 2 lock status(plo2_lock_status)
- Sweep counter in elevation(elevation_sweep_count)
- Antenna power(antenna_power)
- Positioner azimuth velocity(azimuth_scan_rate)
- Temperature measured by sensor on radar control board(local_temp)
- Voltage of 12V power supply(power_supply_12v)
- Noise figure copolar(noise_figure_copol)
- Hot power, cross-polar(hot_power_xpol)
- Low noise amplifier temperature, horizontal channel(temp_lna_h)
- Low noise amplifier temperature, vertical channel(temp_lna_v)
- Cold power, copolar(cold_power_copol)
- Voltage of 15V power supply(power_supply_15v)
- Coolant return temperature(temp_coolant_return)
- Drive power(drive_power)
- Modulator collector current(voltage_modulator_collector_current)
- Voltage proportional to modulator internal temperature(voltage_modulator_temperature)
- Time offset from base_time(time_offset)
- Receiver gain copolar(receiver_gain_copol)
- IF unit temperature(temp_if_unit)
- Sweep counter in azimuth(azimuth_sweep_count)
- Modulator filament status(fil_delay)
- Beam Elevation Angle(elevation)
- Receiver gain cross-polar(receiver_gain_xpol)
- Hot power, copolar(hot_power_copol)
- Noise figure cross-polar(noise_figure_xpol)
- Azimuth of Radar Ray(azimuth)
- Positioner elevation motor current(el_motor_current)
- Humidity measured by probe inside antenna(remote_humidity)
- Voltage proportional to beam voltage, where beam voltage = -50 * value(voltage_beam)
- data_volume_index_number(volume_number)
- Power validity status(power_valid)
- User azimuth cycle count(user_azimuth_cycle_count)
- DC power supply temperature(temp_dc_power_supply)
- Modulator fault status(modulator_fault)
- Humidity measured by sensor on radar control board(local_humidity)
- Voltage of -5V power supply(power_supply_minus5v)
- Synchronization fault status(sync_fault)
- Transmit pulse is enabled(transmit_pulse_enabled)
- Voltage of 5V power supply(power_supply_5v)
- time_in_seconds_since_volume_start(time)
- base time in epoch(base_time)
- Modulator interlock status(interlock_status)
- Voltage of 28V power supply(power_supply_28v)
- Output power(output_power)
- Modulator high voltage on(hv_on)
- Delay for sample trigger to internal scope card, relative to ADC trigger(scope_delay)
- Noise diode temperature, vertical channel(temp_noise_diode_v)
- Noise diode temperature, horizontal channel(temp_noise_diode_h)
- Voltage of 8V power supply(power_supply_8v)
- User elevation cycle count(user_elevation_cycle_count)
- Modulator temperature(temp_modulator)
- Temperature measured by probe inside antenna(remote_temp)
- EIKA temperature(temp_eika)
- Cold power, cross-polar(cold_power_xpol)
- North Latitude(lat)
- -180.0 - +180.0(alt)
- Transmitter fault status(transmitter_temp_fault)
- Description of current scanning mode(pacsi_call_stack)
- Voltage of 5.2V power supply(power_supply_5_2_v)
- Positioner elevation velocity(elevation_scan_rate)
- Fault summary(fault_sum)
- Modulator body current(voltage_body_current)
- Coolant supply temperature(temp_coolant_supply)
- Positioner azimuth motor current(az_motor_current)
more
awrkasacrcwrhiM1.a1: - pulse_repetition_frequency(prt)
- radar_calibration_two_way_radome_loss_h_channel(r_calib_two_way_radome_loss_h)
- calibrated_radar_receiver_gain_v_co_polar_channel(r_calib_receiver_gain_hc)
- Follow mode(follow_mode)
- Sky power, copolar(sky_power_copol)
- Unambiguous range(unambiguous_range)
- Pulse width for this calibration(r_calib_pulse_width)
- lon(lon)
- data_volume_index_number(volume_number)
- altitude(altitude)
- Scan rate, positive for clockwise or increasing elevation(scan_rate)
- East longitude(longitude)
- radiation_frequency(frequency)
- Sky noise, copolar(sky_noise_copol)
- Receiver gain for vertical cross-polar channel 2(r_calib_receiver_gain_vx)
- base time in epoch(base_time)
- platform_type(platform_type)
- Radar measured transmit power, h channel(radar_measured_transmit_power_h)
- North latitude(latitude)
- Unambiguous Doppler velocity(nyquist_velocity)
- Number of samples used to compute moments(n_samples)
- Signal-to-noise-ratio(snr)
- Pulse width(pulse_width)
- Cross-polar propagation phase shift(cross_polar_differential_phase)
- time_in_seconds_since_volume_start(time)
- Beam Elevation Angle(elevation)
- Doppler spectrum width (second moment of the doppler spectrum)(spectral_width)
- reflectivity(reflectivity)
- Index of first ray in sweep, 0-based(sweep_start_ray_index)
- Scan mode for sweep(sweep_mode)
- antenna_is_in_transition_between_sweeps(antenna_transition)
- Noise flor for vertical cross-polar channel 2(r_calib_noise_vx)
- ray_target_fixed_angle(fixed_angle)
- transmit_pulse_mode(prt_mode)
- Time corresponding to last radial in file(time_coverage_end)
- Index for the calibration that applies to each ray(r_calib_index)
- altitude_above_ground_level(altitude_agl)
- Mean doppler velocity(mean_doppler_velocity)
- Time index of last ray in sweep, 0-based(sweep_end_ray_index)
- Transmit power(r_calib_xmit_power_h)
- half_power_radar_beam_width_h_channel(radar_beam_width_h)
- Sweep number, zero-based count(sweep_number)
- Radar beam width, vertical channel(radar_beam_width_v)
- Primary axis of rotation(primary_axis)
- Linear depolarization ratio(linear_depolarization_ratio)
- Sky noise, cross-polarization(sky_noise_xpol)
- Noise floor power for horizontal copolar channel1(r_calib_noise_hc)
- Azimuth of Radar Ray(azimuth)
- Nominal radar antenna gain, v channel(radar_antenna_gain_v)
- Copol to cross-polar correlation coefficient (also known as rhocx)(co_to_crosspol_correlation_coeff)
- Nominal radar antenna gain, h channel(radar_antenna_gain_h)
- Polarization mode(polarization_mode)
- Noise power in noise source region for vertical cross-polar channel(r_calib_noise_source_power_v)
- Noise power in noise source region for horizontal copolar channel 1(r_calib_noise_source_power_h)
- data_volume_start_time_utc(time_coverage_start)
- Distance to the center of the corresponding range bin(range)
- Time offset from base_time(time_offset)
- Time of the calibration that applies to each ray(r_calib_time)
- type_of_instrument(instrument_type)
- Radar constant, horizontal copolar channel 1(r_calib_radar_constant_h)
- Radar constant, vertical cross-polar channel 2(r_calib_radar_constant_v)
- -180.0 - +180.0(alt)
- North Latitude(lat)
- Sky power, cross-polar(sky_power_xpol)
more
|