SGP/S01 - Tower inlet not operational

Inlet not operational in order to change met sensor.

Reported data should not be used.

• (Raw data stream - documentation not supported)

• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  ramped RH(Bbs_R_Wet_Neph3W)
• Relative humidity, Humidograph nephelometer(RH_Neph_Wet)
• Instrument operating mode(mode_flag)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Wet)
• Pressure inside humidified nephelometer(P_Neph_Wet)
• Aerosol total light scattering coefficient, nominal green wavelength at ramped
  RH(Bs_G_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at ramped RH(Bbs_G_Wet_Neph3W)
• Aerosol total light scattering coefficient, nominal blue wavelength at ramped RH(Bs_B_Wet_Neph3W)
• seconds since last impactor transition(seconds_after_transition)
• Correction to humidified nephelometer measurements to standard temperature and
  pressure(density_correction_factor)
• Aerosol total light scattering coefficient, nominal red wavelength at ramped RH(Bs_R_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at ramped RH(Bbs_B_Wet_Neph3W)
• Sample temperature inside humidified nephelometer(T_Neph_Wet)

• (Raw data stream - documentation not supported)

• Blue reference sum(blue_reference_sum)
• Blue overflow count(blue_overflow_count)
• Red overflow count(red_overflow_count)
• Red reference sum(red_reference_sum)
• Blue signal sum(blue_signal_sum)
• Red sample count(red_sample_count)
• Dark sample count(dark_sample_count)
• Blue sample count(blue_sample_count)
• Green signal sum(green_signal_sum)
• Mass flow output(mass_flow_output)
• Dark reference sum(dark_reference_sum)
• Mass flow(mass_flow)
• Dark signal sum(dark_signal_sum)
• Green overflow count(green_overflow_count)
• Reported flags(flags)
• Dark overflow count(dark_overflow_count)
• Red signal sum(red_signal_sum)
• Green sample count(green_sample_count)
• Green reference sum(green_reference_sum)

• Saturation temperature(saturation_temp)
• Cabinet temperature(cabinet_temp)
• Flow read(dilution_flow_reading)
• Flow setpoint(dilution_flow_setpoint)
• Aerosol concentration averaged over times to match N_CCN(concentration)
• Liquid fraction available(fraction_full)
• Liquid level(liquid_level)
• OPC laser current(laser_current)
• Dilution flow valve position(dilution_valve_position)
• Optics temperature(optics_temp)
• Nozzle pressure(nozzle_pressure)
• Condensation temperature(condensation_temp)
• Orifice pressure(orifice_pressure)
• Ambient pressure(ambient_pressure)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• Valve position mass flow controller 2(valve_position_MFC_2)
• Valve position for mass flow controller 1(valve_position_MFC_1)
• Set point for mass flow controller 2(set_point_for_MFC_2)
• Set point for Mass Flow Controller #1(set_point_for_MFC_1)
• Nitrous oxide (N2O) mixing ratio calculated with nominal sensitivity correction(n2o)
• Carbon monoxide (CO) mixing ratio corrected for water vapor concentration and
  calculated with nominal sensitivity correction(co_dry)
• Cell sample pressure(gas_pressure)
• Cell sample temperature(gas_temperature)
• Actual mass flow through MFC #2(mass_flow_through_MFC_2)
• Ambient temperature of instrument(ambient_temperature)
• Actual mass flow through mass flow controller 1(mass_flow_through_MFC_1)
• Measured water content(h2o)
• Nitrous oxide (N2O) mixing ratio corrected for water vapor concentration and
  calculated with nominal sensitivity correction(n2o_dry)
• Carbon monoxide concentration(co)

• Impactor state in terms of aerodynamic diameter cut off(impactor_state)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• Dilution flow valve position(dilution_valve_position)
• Flow setpoint(dilution_flow_setpoint)
• Nozzle pressure(nozzle_pressure)
• Ambient pressure(ambient_pressure)
• Optics temperature(optics_temp)
• Aerosol concentration averaged over times to match N_CCN(concentration)
• Cabinet temperature(cabinet_temp)
• OPC laser current(laser_current)
• Orifice pressure(orifice_pressure)
• Aerosol flow rate(aerosol_flow)
• Saturation temperature(saturation_temp)
• Liquid level(liquid_level)
• Condensation temperature(condensation_temp)
• Liquid fraction available(fraction_full)
• Flow read(dilution_flow_reading)

• Aerosol total light scattering coefficient, nominal red wavelength at dry or
  reference RH(Bs_R_Dry_Neph3W)
• Sample temperature inside reference nephelometer(T_Neph_Dry)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at dry or reference RH(Bbs_G_Dry_Neph3W)
• Aerosol total light scattering coefficient, nominal green wavelength at dry or
  reference RH(Bs_G_Dry_Neph3W)
• Relative humidity, reference nephelometer(RH_Neph_Dry)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  dry or reference RH(Bbs_R_Dry_Neph3W)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Dry)
• Pressure inside reference nephelometer(P_Neph_Dry)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at dry or reference RH(Bbs_B_Dry_Neph3W)
• Instrument operating mode(mode_flag)
• Aerosol total light scattering coefficient, nominal blue wavelength at dry or
  reference RH(Bs_B_Dry_Neph3W)

• AOS Ba_B_CLAP3W transmittance, blue channel(transmittance_B)
• AOS PSAP3W transmittance, green channel(transmittance_G)
• AOS Ba_R_CLAP3W transmittance, red channel(transmittance_R)
• Flow setpoint(dilution_flow_setpoint)
• Diffusion flow valve position(dilution_flow_valve_position)
• Dilution flow rate(dilution_flow)
• Aerosol light absorption coefficient, nominal green wavelength at dry or
  reference RH(Ba_G_PSAP3W)
• Aerosol light absorption coefficient, nominal red wavelength at dry or reference
  RH(Ba_R_PSAP3W)
• Aerosol light absorption coefficient, nominal blue wavelength at dry or
  reference RH(Ba_B_PSAP3W)
• Mass flow(mass_flow)

• (Raw data stream - documentation not supported)

• Diagnostic +15 volts at measurement interface board(diagnostic_voltage_mib_15)
• Pressure compensation state(pressure_compensation_state)
• Instrument temperature compensation state(temperature_compensation_state)
• Diagnostic +5 volts at measurement interface board(diagnostic_voltage_mib_5)
• Instrument test LED state(test_led)
• Diagnostic +24 volts at measurement interface board(diagnostic_voltage_mib_24)
• Sulfur dioxide (SO2) mixing ratio calculated with nominal sensitivity correction(so2)
• Main flow rate(flow)
• Instrument flash lamp state(flash_lamp_state)
• Derived pressure(pressure)
• Instrument PMT status(pmt_status)
• SO2 flag string as an integer value(so2_flags)
• Instrument SO2 coefficient(so2_coefficient)
• Diagnostic voltage +24 volts at motherboard(diagnostic_voltage_mb_24)
• PMT voltage(pmt_volt)
• Distance to the center of the corresponding range bin(range)
• Diagnostic +15 volts at motherboard(diagnostic_voltage_mb_15)
• Diagnostic -15 volts at measurement interface board(diagnostic_voltage_mib_minus_15)
• Instrument purge mode state(purge_mode_state)
• Valve position mass flow controller 2(valve_position_MFC_2)
• Valve position for mass flow controller 1(valve_position_MFC_1)
• Diagnostic +5 volts at motherboard(diagnostic_voltage_mb_5)
• Diagnostic +3.3 volts at measurement interface board(diagnostic_voltage_mib_3p3)
• Instrument lamp setpoint(lamp_setpoint)
• Diagnostic +3.3 volt at motherboard(diagnostic_voltage_mb_3p3)
• Diagnostic -3.3 volts at motherboard(diagnostic_voltage_mb_minus_3p3)
• Reaction chamber temperature(reaction_chamber_temp)
• Measure of the current lamp intensity as a percentage of the nominal maximum(lamp_intensity)
• Averaging time interval(averaging_time)
• Actual mass flow through MFC #2(mass_flow_through_MFC_2)
• Actual mass flow through mass flow controller 1(mass_flow_through_MFC_1)
• Instrument SO2 background correction(so2_background_correction)
• Instrument sample state(gas_mode_state)
• Instrument automatic gain control(automatic_gain_control)
• Lamp voltage(lamp_volt)
• Internal instrument temperature(internal_temp)
• Set point for mass flow controller 2(set_point_for_MFC_2)
• Set point for Mass Flow Controller #1(set_point_for_MFC_1)

• Ambient air temperature(T_Ambient)
• Rain duration(rain_duration)
• Rain amount(rain_amount)
• Heater voltage(heater_volts)
• Wind Direction, relative to true North(WindDirection)
• Wind speed(WindSpeed)
• Rain intensity(rain_intensity)
• Pressure of ambient air(P_Ambient)
• Ambient air relative humidity(RH_Ambient)
• Supply voltage(supply_volts)
• Heater temperature(heater_temp)
• Reference voltage(ref_volts)

• Spot size area(spot_size_area)
• Uncorrected aerosol light absorption coefficient, green channel at dry or
  reference RH(Ba_G_raw)
• Dilution correction factor(dilution_correction_factor)
• Transmittance, red channel(transmittance_red)
• Transmittance, blue channel(transmittance_blue)
• Aerosol light absorption coefficient, green channel at dry or reference RH(Ba_G_Weiss)
• Aerosol light absorption coefficient, blue channel at dry or reference RH(Ba_B_Weiss)
• Volume of air through each filter corrected for dilution(sample_volume)
• Instrument flow rate(sample_flow_rate)
• Uncorrected aerosol light absorption coefficient, red channel at dry or
  reference RH(Ba_R_raw)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Transmittance, green channel(transmittance_green)
• Uncorrected aerosol light absorption coefficient, blue channel at dry or
  reference RH(Ba_B_raw)
• Aerosol light absorption coefficient, red channel at dry or reference RH(Ba_R_Weiss)
• Filter state(filter_unstable)

• Uncorrected aerosol total light scattering coefficient, nominal red wavelength
  at dry or reference RH(Bs_R_Dry_Neph3W_raw)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at dry or reference RH(Bbs_B_Dry_Neph3W)
• Aerosol total light scattering coefficient, nominal red wavelength at dry or
  reference RH(Bs_R_Dry_Neph3W)
• Uncorrected aerosol total light scattering coefficient, nominal green wavelength
  at dry or reference RH(Bs_G_Dry_Neph3W_raw)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Dry)
• Pressure inside reference nephelometer(P_Neph_Dry)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal blue
  wavelength at dry or reference RH(Bbs_B_Dry_Neph3W_raw)
• Aerosol total light scattering coefficient, nominal blue wavelength at dry or
  reference RH(Bs_B_Dry_Neph3W)
• Relative humidity, reference nephelometer(RH_Neph_Dry)
• Aerosol total light scattering coefficient, nominal green wavelength at dry or
  reference RH(Bs_G_Dry_Neph3W)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal red
  wavelength at dry or reference RH(Bbs_R_Dry_Neph3W_raw)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal green
  wavelength at dry or reference RH(Bbs_G_Dry_Neph3W_raw)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Sample temperature inside reference nephelometer(T_Neph_Dry)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at dry or reference RH(Bbs_G_Dry_Neph3W)
• Uncorrected aerosol total light scattering coefficient, nominal blue wavelength
  at dry or reference RH(Bs_B_Dry_Neph3W_raw)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  dry or reference RH(Bbs_R_Dry_Neph3W)

• (Raw data stream - documentation not supported)

• Sampling mode scan type(scan_type)
• Humidified DMA scanning time instrument setting(scan_time_setting)
• Minimum aerosol particle diameter instrument setting(scan_min_diameter_setting)
• Concentration of aerosol(aerosol_concentration)
• Total scan concentration over all bins(total_concentration)
• Humid aerosol particle relative humidity(humid_rh)
• Sample flow rate(sample_flow)
• Bin center value(bin_center)
• Dry aerosol diameter size instrument setting(dry_diameter_setting)
• Atomizer calibration status(atomizer)
• Number of bins stored in data block(num_bins)
• Bin width(bin_width)
• Maximum aerosol particle diameter instrument setting(scan_max_diameter_setting)
• Bin numbers for sweep measurements(bin)
• Dry aerosol particle relative humidity instrument setting(dry_rh_setting)

• Low voltage reading(low_voltage)
• Tube length(tube_length)
• Gas viscosity(gas_viscosity)
• Nanoparticle agglomerate mobility analysis(nanoparticle_agglomerate_mobility_analysis)
• High voltage reading(high_voltage)
• Aerosol flow rate(aerosol_flow)
• Mean free path(mean_free_path)
• Mode index(mode)
• Total scan concentration over all bins(total_concentration)
• Sutherland constant(Sutherland_constant)
• Reference mean free path(reference_mean_free_path)
• Sample relative humidity(sample_relative_humidity)
• Reference gas pressure(reference_gas_pressure)
• Number size distribution (dN/dlogDp)(number_size_distribution)
• Diffusion correction(diffusion_correction)
• Flag indicating aeri retrieval status(status_flag)
• Median diameter of size distribution(median)
• Bypass flow rate set point(bypass_flow)
• Sample pressure(sample_pressure)
• Sample temperature(sample_temperature)
• Mean diameter of size distribution using a geometric average(geometric_mean)
• HV polarity(hv_polarity)
• Lower size limit(lower_size)
• Mean diameter of size distribution(mean)
• Multiple charge correction(multiple_charge_correction)
• Reference gas viscosity(reference_gas_viscosity)
• Tube diameter(tube_diameter)
• Bins for diameter midpoint measurements(diameter_midpoint)
• Reference gas temperature(reference_gas_temperature)
• Sheath flow(sheath_flow)
• Inner radius of DMA(DMA_inner_radius)
• 50 percent cut-point diameter of the impactor(d50)
• Calculated time for the aerosol to flow through the sample column of the
  classifier(flow_time)
• Standard deviation of mean diameter of size distribution using geometric average(geometric_mean_std)
• Outer radius of DMA(DMA_outer_radius)
• Characteristic length of DMA(DMA_characteristic_length)

• Flow setpoint(dilution_flow_setpoint)
• Calibrated aerosol flow as supplied by mentor(aerosol_flow_calibrated)
• Dilution slope(dilution_slope)
• Nozzle pressure(nozzle_pressure)
• Condensation temperature(condensation_temp)
• Dilution correction factor(dilution_correction_factor)
• Ambient pressure(ambient_pressure)
• Dilution flow valve position(dilution_valve_position)
• OPC laser current(laser_current)
• Aerosol concentration averaged over times to match N_CCN(concentration)
• Liquid level(liquid_level)
• Liquid fraction available(fraction_full)
• Optics temperature(optics_temp)
• Saturation temperature(saturation_temp)
• Dilution intercept(dilution_intercept)
• Orifice pressure(orifice_pressure)
• Flow read(dilution_flow_reading)
• Cabinet temperature(cabinet_temp)

• Measured water content(h2o)
• Valve position for mass flow controller 1(valve_position_MFC_1)
• Valve position mass flow controller 2(valve_position_MFC_2)
• Ambient temperature of instrument(ambient_temperature)
• Nitrous oxide (N2O) mixing ratio corrected for water vapor concentration and
  calculated with nominal sensitivity correction(n2o_dry)
• Seconds after last calibration(seconds_after_calibration)
• Cell sample pressure(gas_pressure)
• Carbon monoxide concentration(co)
• Nitrous oxide (N2O) mixing ratio calculated with nominal sensitivity correction(n2o)
• Actual mass flow through MFC #2(mass_flow_through_MFC_2)
• Actual mass flow through mass flow controller 1(mass_flow_through_MFC_1)
• Carbon monoxide (CO) mixing ratio corrected for water vapor concentration and
  calculated with nominal sensitivity correction(co_dry)
• Cell sample temperature(gas_temperature)
• Set point for mass flow controller 2(set_point_for_MFC_2)
• Set point for Mass Flow Controller #1(set_point_for_MFC_1)

• Reference(reference)
• Lower particle size limit for each bin(lower_size_limit)
• Unit temperature(unit_temperature)
• Auxiliary measurement, not implemented(auxiliary)
• Temperature used for calculation(temperature)
• Purge flow(purge_flow)
• Main flow rate(flow)
• Bin number(bin_num)
• Sheath flow(sheath_flow)
• Sample pressure(sample_pressure)
• Sample volume(sampling_volume)
• Particle size distribution(size_distribution)
• Scatter signal(scattering_voltage)
• Differential_voltage, see instrument manual(differential_voltage)
• Current(current)
• Upper particle size limit for each bin(upper_size_limit)

• Hourly average of P_Neph_Dry when impactor state reports as 10. When state is
  10, the sample being measured is 10 um or smaller.(P_10um_hourly_average)
• P_10um_hourly_average minus P_1um_hourly_average(dP_10um_minus_1um)
• Relative humidity at the impactor inlet(impactor_inlet_RH)
• Hourly average of P_Neph_Dry when impactor state reports as 1. When state is 1,
  the sample being measured is 1 um or smaller.(P_1um_hourly_average)
• seconds since last impactor transition(seconds_after_transition)
• Pressure inside reference nephelometer(P_Neph_Dry)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)

• (Raw data stream - documentation not supported)

• Aerosol total light scattering coefficient, nominal blue wavelength at ramped RH(Bs_B_Wet_Neph3W)
• Instrument operating mode(mode_flag)
• Aerosol total light scattering coefficient, nominal red wavelength at ramped RH(Bs_R_Wet_Neph3W)
• Aerosol total light scattering coefficient, nominal green wavelength at ramped
  RH(Bs_G_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  ramped RH(Bbs_R_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at ramped RH(Bbs_G_Wet_Neph3W)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Wet)
• Pressure inside humidified nephelometer(P_Neph_Wet)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at ramped RH(Bbs_B_Wet_Neph3W)
• Sample temperature inside humidified nephelometer(T_Neph_Wet)
• Relative humidity, Humidograph nephelometer(RH_Neph_Wet)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• OPC laser current(laser_current)
• Condensation temperature(condensation_temp)
• Aerosol concentration averaged over times to match N_CCN(concentration)
• Ambient pressure(ambient_pressure)
• Nozzle pressure(nozzle_pressure)
• Orifice pressure(orifice_pressure)
• Cabinet temperature(cabinet_temp)
• Aerosol flow rate(aerosol_flow)
• Liquid fraction available(fraction_full)
• Liquid level(liquid_level)
• Optics temperature(optics_temp)
• Saturation temperature(saturation_temp)

• Ozone bench temperature(ozone_bench_temp)
• Ozone concentration(ozone)
• Ozone pressure(ozone_pressure)

• Uncorrected aerosol total light scattering coefficient, nominal blue wavelength
  at ramped RH(Bs_B_Wet_Neph3W_raw)
• Aerosol total light scattering coefficient, nominal red wavelength at ramped RH(Bs_R_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  ramped RH(Bbs_R_Wet_Neph3W)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal red
  wavelength at ramped RH(Bbs_R_Wet_Neph3W_raw)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Relative humidity, Humidograph nephelometer(RH_Neph_Wet)
• Sample temperature inside humidified nephelometer(T_Neph_Wet)
• Uncorrected aerosol total light scattering coefficient, nominal green wavelength
  at ramped RH(Bs_G_Wet_Neph3W_raw)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal blue
  wavelength at ramped RH(Bbs_B_Wet_Neph3W_raw)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at ramped RH(Bbs_G_Wet_Neph3W)
• Aerosol total light scattering coefficient, nominal green wavelength at ramped
  RH(Bs_G_Wet_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at ramped RH(Bbs_B_Wet_Neph3W)
• Uncorrected aerosol total light scattering coefficient, nominal red wavelength
  at ramped RH(Bs_R_Wet_Neph3W_raw)
• Aerosol total light scattering coefficient, nominal blue wavelength at ramped RH(Bs_B_Wet_Neph3W)
• Uncorrected aerosol back-hemispheric light scattering coefficient, nominal green
  wavelength at ramped RH(Bbs_G_Wet_Neph3W_raw)
• Pressure inside humidified nephelometer(P_Neph_Wet)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Wet)

• Aerosol total light scattering coefficient, nominal blue wavelength at dry or
  reference RH(Bs_B_Dry_Neph3W)
• Temperature, reference nephelometer inlet(T_Neph_Inlet_Dry)
• Instrument operating mode(mode_flag)
• Sample temperature inside reference nephelometer(T_Neph_Dry)
• Relative humidity, reference nephelometer(RH_Neph_Dry)
• Aerosol total light scattering coefficient, nominal red wavelength at dry or
  reference RH(Bs_R_Dry_Neph3W)
• Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
  dry or reference RH(Bbs_R_Dry_Neph3W)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Pressure inside reference nephelometer(P_Neph_Dry)
• Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
  at dry or reference RH(Bbs_B_Dry_Neph3W)
• Correction to humidified nephelometer measurements to standard temperature and
  pressure(density_correction_factor)
• Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
  at dry or reference RH(Bbs_G_Dry_Neph3W)
• Aerosol total light scattering coefficient, nominal green wavelength at dry or
  reference RH(Bs_G_Dry_Neph3W)
• seconds since last impactor transition(seconds_after_transition)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• Aerosol light absorption coefficient, red channel at dry or reference RH(Ba_R_Weiss)
• Instrument flow rate(sample_flow_rate)
• Volume of air through each filter corrected for dilution(sample_volume)
• Spot size area(spot_size_area)
• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Aerosol light absorption coefficient, green channel at dry or reference RH(Ba_G_Weiss)
• Aerosol light absorption coefficient, blue channel at dry or reference RH(Ba_B_Weiss)
• Transmittance, blue channel(transmittance_blue)
• Transmittance, green channel(transmittance_green)
• Uncorrected aerosol light absorption coefficient, green channel at dry or
  reference RH(Ba_G_raw)
• Uncorrected aerosol light absorption coefficient, blue channel at dry or
  reference RH(Ba_B_raw)
• Transmittance, red channel(transmittance_red)
• Uncorrected aerosol light absorption coefficient, red channel at dry or
  reference RH(Ba_R_raw)

• CCN temperature gradient, second CCN(CCN_temperature_gradient_2)
• CCN temperature gradient, first CCN(CCN_temperature_gradient_1)
• AOS CCN set point for temperature at middle of column, first CCN(CCN_T_set_TEC2_1)
• AOS CCN set point for temperature at middle of column, second column(CCN_T_set_TEC2_2)
• CCN alarm code expressed as a summation of powers of 2. 0 indicates no detected
  problem, first column(CCN_alarm_code_1)
• CCN alarm code expressed as a summation of powers of 2. 0 indicates no detected
  problem, second column(CCN_alarm_code_2)
• AOS CCN voltage used by DMT for OPC diagnostic purposes, first CCN(CCN_baseline_monitor_1)
• AOS CCN voltage used by DMT for OPC diagnostic purposes, second column(CCN_baseline_monitor_2)
• AOS CCN set point for temperature at top of column, first column(CCN_T_set_TEC1_1)
• AOS CCN set point for temperature at top of column, second column(CCN_T_set_TEC1_2)
• Droplet bin bounds(size_bin_bounds)
• AOS number concentration of CCN at supersaturation step 1(N_CCN_1)
• AOS number concentration of CCN at supersaturation step 2(N_CCN_2)
• AOS CCN (read) temperature at bottom of column, second CCN(CCN_T_read_TEC3_2)
• AOS CCN (read) temperature at bottom of column, first CCN(CCN_T_read_TEC3_1)
• CCN Proportional valve voltage, first column(CCN_proportional_valve_voltage_1)
• CCN Proportional valve voltage, second column(CCN_proportional_valve_voltage_2)
• AOS CCN set point for temperature at bottom of column, first CCN(CCN_T_set_TEC3_1)
• AOS CCN set point for temperature at bottom of column, second column(CCN_T_set_TEC3_2)
• First stage monitor voltage, second column(CCN_first_stage_monitor_voltage_2)
• First stage monitor voltage, first column(CCN_first_stage_monitor_voltage_1)
• AOS CCN observed temperature at top of column, first CCN(CCN_T_read_TEC1_1)
• AOS CCN observed temperature at top of column, second CCN(CCN_T_read_TEC1_2)
• AOS CCN observed temperature at middle of column, second column(CCN_T_read_TEC2_2)
• AOS CCN observed temperature at middle of column, first column(CCN_T_read_TEC2_1)
• AOS CCN logical value, indicating whether the instrument has reached thermal
  gradient stabilization and is within 0.4 degrees C of the set point, first
  column(CCN_temp_unstable_1)
• AOS CCN logical value, indicating whether the instrument has reached thermal
  gradient stabilization and is within 0.4 degrees C of the set point, second
  column(CCN_temp_unstable_2)
• AOS bin number of lowest channel of OPC include in summation of N_CCN, first
  column(N_CCN_bin_number_1)
• AOS bin number of lowest channel of OPC include in summation of N_CCN, second
  column(N_CCN_bin_number_2)
• AOS CCN sample pressure, second CCN(CCN_P_sample_2)
• AOS CCN sample pressure, first column(CCN_P_sample_1)
• AOS CCN temperature of sample air at entrance to instrument, second CCN(CCN_T_inlet_2)
• AOS CCN temperature of sample air at entrance to instrument, first_column(CCN_T_inlet_1)
• AOS CCN number concentration by bin, second CCN(N_CCN_dN_2)
• AOS CCN droplet count by bin size, first column(N_CCN_dN_1)
• Size bins for CCN droplet count(size_bin)
• AOS CCN volumetric flowrate of sample air, first CCN(CCN_Q_sample_1)
• AOS CCN temperature of sample air entering the column, first column(CCN_T_sample_1)
• AOS CCN volumetric flowrate of sample air, second CCN(CCN_Q_sample_2)
• AOS CCN temperature of sample air entering the column, second column(CCN_T_sample_2)
• AOS CCN Nafion temperature, first CCN(CCN_T_nafion_1)
• AOS CCN Nafion temperature, second column(CCN_T_nafion_2)
• AOS CCN OPC laser current, second column(CCN_laser_current_2)
• AOS CCN OPC laser current, first column(CCN_laser_current_1)
• AOS CCN set point temperature for the inlet manifold, first column(CCN_T_inlet_set_1)
• AOS CCN temperature of sample air at entrance to instrument, second column(CCN_T_inlet_set_2)
• AOS CCN sample supersaturation set point value reported by instrument, first
  column(CCN_supersaturation_set_point_1)
• AOS CCN sample supersaturation set point value reported by instrument, second
  column(CCN_supersaturation_set_point_2)
• Number of particles that are larger than 10um, first column(CCN_overflow_1)
• Number of particles that are larger than 10um, second column(CCN_overflow_2)
• AOS CCN set temperature for the Nafion humidifier, second column(CCN_T_nafion_set_2)
• AOS CCN set point temperature for the optical partical counter (OPC), first CCN(CCN_OPC_set_1)
• AOS CCN set temperature for the Nafion humidifier, first column(CCN_T_nafion_set_1)
• AOS CCN set point temperature for the optical partical counter (OPC), second CCN(CCN_OPC_set_2)
• AOS CCN temperature of the optical particle counter, first column(CCN_T_OPC_1)
• AOS CCN temperature of the optical particle counter, second column(CCN_T_OPC_2)
• AOS CCN volumetric flowrate of sheath air, second CCN(CCN_Q_sheath_2)
• AOS CCN volumetric flow rate of sheath air, first column(CCN_Q_sheath_1)

• Instrument sample state(gas_mode_state)
• Distance to the center of the corresponding range bin(range)
• PMT voltage(pmt_volt)
• Instrument SO2 background correction(so2_background_correction)
• Set point for mass flow controller 2(set_point_for_MFC_2)
• Set point for Mass Flow Controller #1(set_point_for_MFC_1)
• Actual mass flow through mass flow controller 1(mass_flow_through_MFC_1)
• Actual mass flow through MFC #2(mass_flow_through_MFC_2)
• Seconds after last calibration(seconds_after_calibration)
• Lamp voltage(lamp_volt)
• SO2 flag string as an integer value(so2_flags)
• Instrument purge mode state(purge_mode_state)
• Sulfur dioxide (SO2) mixing ratio calculated with nominal sensitivity correction(so2)
• Valve position mass flow controller 2(valve_position_MFC_2)
• Valve position for mass flow controller 1(valve_position_MFC_1)
• Main flow rate(flow)
• Instrument temperature compensation state(temperature_compensation_state)
• Instrument lamp setpoint(lamp_setpoint)
• Instrument automatic gain control(automatic_gain_control)
• Instrument test LED state(test_led)
• Internal instrument temperature(internal_temp)
• Instrument SO2 coefficient(so2_coefficient)
• Averaging time interval(averaging_time)
• Reaction chamber temperature(reaction_chamber_temp)
• Derived pressure(pressure)
• Instrument PMT status(pmt_status)
• Instrument flash lamp state(flash_lamp_state)
• Pressure compensation state(pressure_compensation_state)
• Measure of the current lamp intensity as a percentage of the nominal maximum(lamp_intensity)

• Impactor state in terms of aerodynamic diameter cut off(impactor_state)
• Normalization factor for green transmittance, resets with each filter change(transmittance_green_normalization_factor)
• PSAP3W front panel transmittance relative to new filter, green channel(tr_green)
• Normalization factor for red transmittance, resets with each filter change(transmittance_red_normalization_factor)
• Transmittance, red channel, not normalized(transmittance_red_raw)
• Transmittance, blue channel(transmittance_blue)
• Transmittance, red channel(transmittance_red)
• Light absorbance, red channel(absorbance_red)
• Diffusion flow valve position(dilution_flow_valve_position)
• Transmittance, green channel, not normalized(transmittance_green_raw)
• Transmittance, green channel(transmittance_green)
• PSAP3W front panel transmittance relative to new filter, red channel(tr_red)
• Normalization factor for blue transmittance, resets with each filter change(transmittance_blue_normalization_factor)
• Transmittance, blue channel, not normalized(transmittance_blue_raw)
• seconds since last impactor transition(seconds_after_transition)
• Dilution flow rate(dilution_flow)
• Dilution correction factor(dilution_correction_factor)
• Spot size area(spot_size_area)
• PSAP3W front panel transmittance relative to new filter, blue channel(tr_blue)
• Light absorbance, blue channel(absorbance_blue)
• Filter state(filter_unstable)
• Flow setpoint(dilution_flow_setpoint)
• Instrument flow rate(sample_flow_rate)
• Light absorbance, green channel(absorbance_green)

• (Raw data stream - documentation not supported)

• (Raw data stream - documentation not supported)

• Sample temperature(sample_temperature)
• Outer radius of DMA(DMA_outer_radius)
• Reference gas viscosity(reference_gas_viscosity)
• High voltage reading(high_voltage)
• Gas viscosity(gas_viscosity)
• Reference mean free path(reference_mean_free_path)
• Mode index(mode)
• Tube length(tube_length)
• Diffusion correction(diffusion_correction)
• Reference gas pressure(reference_gas_pressure)
• Low voltage reading(low_voltage)
• Standard deviation of mean diameter of size distribution using geometric average(geometric_mean_std)
• Calculated time for the aerosol to flow through the sample column of the
  classifier(flow_time)
• Bypass flow rate set point(bypass_flow)
• 50 percent cut-point diameter of the impactor(d50)
• Nanoparticle agglomerate mobility analysis(nanoparticle_agglomerate_mobility_analysis)
• Sample relative humidity(sample_relative_humidity)
• Number size distribution (dN/dlogDp)(number_size_distribution)
• Total scan concentration over all bins(total_concentration)
• Sheath flow(sheath_flow)
• Sutherland constant(Sutherland_constant)
• Sample pressure(sample_pressure)
• Median diameter of size distribution(median)
• Lower size limit(lower_size)
• Flag indicating aeri retrieval status(status_flag)
• Reference gas temperature(reference_gas_temperature)
• Aerosol flow rate(aerosol_flow)
• Bins for diameter midpoint measurements(diameter_midpoint)
• HV polarity(hv_polarity)
• Characteristic length of DMA(DMA_characteristic_length)
• Inner radius of DMA(DMA_inner_radius)
• Multiple charge correction(multiple_charge_correction)
• Mean diameter of size distribution(mean)
• Mean free path(mean_free_path)
• Tube diameter(tube_diameter)
• Mean diameter of size distribution using a geometric average(geometric_mean)

• AOS CCN set point temperature for the inlet manifold(CCN_T_inlet_set)
• Temperature difference between CCN_t_set_TEC3 and CCN_t_set_TEC1(CCN_temperature_gradient)
• Size bins for CCN droplet count(size_bin)
• First stage monitor voltage(CCN_first_stage_monitor_voltage)
• CCN Proportional valve voltage(CCN_proportional_valve_voltage)
• Cloud condensation nuclei number density(N_CCN)
• AOS CCN voltage used by DMT for OPC diagnostic purposes(CCN_baseline_monitor)
• CCN alarm code expressed as a summation of powers of 2. 0 indicates no detected
  problem(CCN_alarm_code)
• AOS CCN OPC laser current(CCN_laser_current)
• AOS CCN set point temperature for the optical particle counter (OPC)(CCN_OPC_set)
• AOS CCN volumetric flowrate of sheath air(CCN_Q_sheath)
• AOS CCN set point for temperature at bottom of column(CCN_T_set_TEC3)
• AOS CCN number concentration by bin(N_CCN_dN)
• AOS CCN temperature of the optical particle counter(CCN_T_OPC)
• AOS CCN set point for temperature at middle of column(CCN_T_set_TEC2)
• AOS CCN set point for temperature at top of column(CCN_T_set_TEC1)
• AOS CCN temperature of sample air entering the column(CCN_T_sample)
• AOS CCN sample pressure(CCN_P_sample)
• AOS CCN sample supersaturation set point value reported by instrument(CCN_supersaturation_set_point)
• AOS CCN (read) temperature at bottom of column(CCN_T_read_TEC3)
• AOS CCN observed temperature at middle of column(CCN_T_read_TEC2)
• AOS CCN observed temperature at top of column(CCN_T_read_TEC1)
• AOS CCN temperature of the nafion humidifier(CCN_T_nafion)
• AOS CCN volumetric flowrate of sample air(CCN_Q_sample)
• Bin number of lowest channel of OPC include in summation of N_CCN(N_CCN_bin_number)
• AOS CCN logical value, indicating whether the instrument has reached thermal
  gradient stabilization and is within 0.4 degrees C of the set point(CCN_temp_unstable)
• AOS CCN set temperature for the Nafion humidifier(CCN_T_nafion_set)
• Droplet bin bounds(size_bin_bounds)
• AOS CCN temperature of sample air at entrance to instrument(CCN_T_inlet)
• Number of particles that are larger than 10um(CCN_overflow)