TWP/SMET/C3 - Rain blocked pressure port

Atmospheric pressure values were suspect due to anomolous readings during heavy rain 
events.  Suspect blockage of port due to rainfall.  New logger and enclosure corrected problem.

• Atmospheric pressure(atmos_pressure)

TWP/SMET/C3 - Data missing due to Logger Change

All Data from this site are missing during this time period due to a change of the 
collection system, logger and enclosure.  Data resumed after change.

• External voltage(external_voltage)
• north latitude for all the input platforms.(lat)
• Time offset of tweaks from base_time(time_offset)
• Precipitation maximum(precip_max)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Internal voltage(internal_voltage)
• Wind #1 speed minimum(wind1_spd_min)
• Internal Logger Temperature(logger_temp)
• Wind #2 speed maximum(wind2_spd_max)
• precipitation minimum(precip_min)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #1 speed maximum(wind1_spd_max)
• Mean Air Temperature or Hardware Error(temp_mean)
• Max Temperature at lowest Model Level- 1 hr(temp_max)
• Vapor pressure mean(vappress_mean)
• Atmospheric pressure(atmos_pressure)
• Vapor pressure standard deviation(vappress_sd)
• Relative humidity mean(relh_mean)
• Relative humidity maximum(relh_max)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)
• Bit data. See details.(bit_data)
• Precipitation mean(precip_mean)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Time offset from base_time(base_time)
• Min Temperature at lowest Model Level- 1 hr(temp_min)
• altitude above sea levelaltunits(alt)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Precipitation standard deviation(precip_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• east longitude for all the input platforms.(lon)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 speed standard deviation(wind2_spd_sd)
• Temperature standard deviation(temp_sd)

TWP/SMET/C3 - Negative rainfall rates

Due to limitations of the Zeno dataloggers all voltage measurements
from the optical rain gauge (ORG) were converted to rainfall rates. 
This resulted in negative values for rain rates.  Any value below
0.10 mm/hr should be considered to be 0 mm/hr.  New dataloggers 
alleviated this problem.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Reprocess: Incorrect Units Listed for Vapor Pressure

The netcdf file header incorrectly listed the units of Vapor Pressure as hPa when in fact 
they were kPa.

• Vapor pressure standard deviation(vappress_sd)
• Vapor pressure mean(vappress_mean)

TWP/SMET/C3 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Atmospheric pressure(atmos_pressure)

TWP/SMET/C3 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the SMET suite of instruments effective 20060926. 
 Two new variables (count and rain amount) were added at the end of the twpsmet60sC1.b1 
datastream.  When reprocessing of this datastream occurs these variables will be added 
with -9999 (missing) as the value for dates prior to gauge installation.

• Time offset from base_time(base_time)