Data Quality Reports for Session: 104515 User: delta Completed: 02/27/2007


TABLE OF CONTENTS

DQR IDSubjectData Streams Affected
D000531.2SGP/EBBR/E13 - Data Missing Due to Power Failuresgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D000531.3SGP/EBBR/E13 - Data missing or corruptedsgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D000531.4SGP/EBBR/E13 - failure of sensorssgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D000531.5SGP/EBBR/E13 - Failed Right Humidity Probesgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D000628.1SGP/EBBR/E13- Left humidity probe replacedsgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D020628.16SGP/EBBR/E13 - T/RH Checksgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D020628.2SGP/EBBR/E13 - 3-month Checksgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D020723.1SGP/EBBR/E13 - Thermocouple out of range, data incorrectsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D930428.2SGP/EBBR/E13 - incorrect home signalsgp5ebbrE13.a0, sgp30ebbrE13.a1
D930503.2SGP/EBBR/E13 - incorrect meteorological observationssgp5ebbrE13.a0, sgp30ebbrE13.a1
D931108.3SGP/EBBR/E13 - pressure calibrationsgp30ebbrE13.a1
D931108.4SGP/EBBR/E13 - solid moisture correctionsgp30ebbrE13.a1
D940106.5SGP/EBBR/E13 - Invalid data during disconnection of AEM at E13sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D940511.2SGP/EBBR/E13 - SM4 Replacementsgp15ebbrE13.a1, sgp30ebbrE13.a1
D941021.5SGP/EBBR/E13 - Soil Temperature Aberationssgp15ebbrE13.a1, sgp30ebbrE13.a1
D941208.1SGP/EBBR/E13 - Net Radiation - Hemisphere Replacementsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D950126.1SGP/EBBR/E13 - Incorrect Soil Temperature #4sgp15ebbrE13.a1, sgp30ebbrE13.a1
D950626.1SGP/EBBR/E13 - Frozen Wind Speed Sensorsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D950626.2SGP/EBBR/E13 - Frozen Wind Speed Sensorsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D950626.7SGP/EBBR/E13 - Reprocess: Soil Temperature Malfunctionsgp15ebbrE13.a1, sgp30ebbrE13.a1
D950815.2SGP/EBBR/E13 - Low Battery Voltage and AEM Left on Manualsgp5ebbrE13.a0, sgp30ebbrE13.a1
D950828.1SGP/EBBR/E13 - Battery Voltage Dropsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D951113.1SGP/EBBR/E13 - Wind Direction Set Pin Slippagesgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D951113.6SGP/EBBR/E13 - Battery voltage dropsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D951116.1SGP/EBBR/E13 - AEM Exchange Stopped in Snow and Freezing Rainsgp30ebbrE13.a1
D951220.2SGP/EBBR/E13 - Missing datasgp5ebbrE13.a0, sgp30ebbrE13.a1
D951220.6SGP/EBBR/E13 - battery voltage dropsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D960104.1SGP/EBBR/E13 - EBBR down - Data Missingsgp5ebbrE13.a0, sgp30ebbrE13.a1
D960508.6SGP/EBBR/E13 - 3-month checksgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D960606.1SGP/EBBR/E13 - Annual Calibration changeoutsgp5ebbrE13.a0, sgp30ebbrE13.a1
D961122.11SGP/EBBR/E13 - Wind Direction Incorrectsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D961122.24SGP/EBBR/E13 - EBBR 3 Month Checks - 10 EFssgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D970330.1SGP/EBBR/E13 - Frozen Wind Speed Sensorsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D970730.3SGP/EBBR/E13 - CR10 Malfunctionsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D971017.5SGP/EBBR/E13 - Missing Datasgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D971021.5SGP/EBBR/E13 - EBBR Biannual Checkssgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D980117.19SGP/EBBR/E13- EBBR Frozen Wind Speedsgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D980117.27SGP/EBBR/E13 - EBBR AEMs Not Exchanging (Iced Or Fuse Blown)sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
D980416.12SGP/EBBR/E13 - 3-Month Checksgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1


DQRID : D000531.2
Start DateStart TimeEnd DateEnd Time
07/17/1995080007/17/19952200
Subject:
SGP/EBBR/E13 - Data Missing Due to Power Failure
DataStreams:sgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
A power failure following a lightning strike to the central cluster
area resulted in the EBBR data being missing for this period of time.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp5ebbrE13.00:
  • Raw data stream - documentation not supported(Raw data stream - documentation not supported)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D000531.3
Start DateStart TimeEnd DateEnd Time
07/24/1995130007/24/19952300
Subject:
SGP/EBBR/E13 - Data missing or corrupted
DataStreams:sgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
Data are missing or corrupted during this period due to a broken wire
on the solar panel that lowered the voltage to the system and maintenance
that took place from 1530 to about 2215 GMT.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp5ebbrE13.00:
  • Raw data stream - documentation not supported(Raw data stream - documentation not supported)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D000531.4
Start DateStart TimeEnd DateEnd Time
07/17/1995220007/24/19952300
Subject:
SGP/EBBR/E13 - failure of sensors
DataStreams:sgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
A lightning strike to the central cluster area shortly after 0800 GMT
on July 17 caused failure of several EBBR sensors: both humidity probes,
the barometer, soil heat flux #3, soil moisture # 1 and the wind
direction.
These failed sensors caused sensible, latent, and average soil heat flux
to be incorrect until site operations performed maintenance on July 24th.

Site Operations found a loose connection from soil moisture probe #1, 
removed barometer SN 6578 and replaced it with SN 6507, removed soil heat 
flux sensor #3 with SN 923022 and replaced it with SN 933199, repositioned 
the wind direction sensor - which was rotated approximately ninety degrees 
clockwise from its proper position, and removed the right humidity probe 
SN 460412 and replaced it with SN 460428.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • top vapor pressure(vp_top)
  • top relative humidity(hum_top)
  • bottom vapor pressure(vp_bot)

sgp5ebbrE13.00:
  • Raw data stream - documentation not supported(Raw data stream - documentation not supported)

sgp15ebbrE13.a1:
  • Left relative humidity(mv_hum_l)
  • Temperature of left humidity sensor chamber(rr_thum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)


Back To Table of Contents

DQRID : D000531.5
Start DateStart TimeEnd DateEnd Time
07/17/1995220009/22/19952108
Subject:
SGP/EBBR/E13 - Failed Right Humidity Probe
DataStreams:sgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
A lightning strike to the central cluster area on 17 July 1995 caused
failure of several EBBR sensors including the right humidity probe.
On July 24th, site operations removed the right humidity probe SN 460412 and 
replaced it with SN 460428

In less than a day the right humidity probe output soared to over 113% and
has hovered around 112% since.  I consider all right probe values to be
incorrect due to this behavior.

Without a properly functioning right humidity probe, all values of top and
bottom relative humidity, top and bottom vapor pressure, Bowen
ratio, and latent and sensible heat fluxes are incorrect.

A working spare relative humidity probe was not available at that time.
The probe was replaced with a working, calibrated probe on 22 September 1995
at about 2108 GMT.  I have the examined the data since the day of the
replacement and find that the new probe is working well.  All E13 EBBR
measurements are presently correct.  The old probe S/N was 460428, the new
S/N is 460413.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • top vapor pressure(vp_top)
  • top relative humidity(hum_top)
  • bottom vapor pressure(vp_bot)

sgp5ebbrE13.00:
  • Raw data stream - documentation not supported(Raw data stream - documentation not supported)

sgp15ebbrE13.a1:
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Right relative humidity(mv_hum_r)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)


Back To Table of Contents

DQRID : D000628.1
Start DateStart TimeEnd DateEnd Time
07/17/1995220007/25/19951930
Subject:
SGP/EBBR/E13- Left humidity probe replaced
DataStreams:sgp5ebbrE13.00, sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
A lightning strike to the central cluster area on 17 July 1995 caused the
left humidity probe to fail.  Some of the period of incorrect data has been
 discussed in D0000531.4.  The left humidity probe was replaced on 25 July 
1995 at 1925 GMT (old SN 460413, new SN 460435).
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • top vapor pressure(vp_top)
  • top relative humidity(hum_top)
  • bottom vapor pressure(vp_bot)

sgp5ebbrE13.00:
  • Raw data stream - documentation not supported(Raw data stream - documentation not supported)

sgp15ebbrE13.a1:
  • Left relative humidity(mv_hum_l)
  • Temperature of left humidity sensor chamber(rr_thum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)


Back To Table of Contents

DQRID : D020628.16
Start DateStart TimeEnd DateEnd Time
11/04/1994200511/04/19942100
Subject:
SGP/EBBR/E13 - T/RH Check
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During the month of November 1994, site operations personnel conducted
field comparisons of the temperature and relative humidity sensors in the
EBBRs and the HMI31 portable T/RH meter (with the removable probe).  As is
reflected in the home signal output, the automatic exchange mechanism was
disabled in order to conduct the checks.

Measurements were taken every 5 minutes, for a half hour each in the
aspirated radiation shields (the HMI31 was inserted into the EBBR aspirated
radiation shield to provide the same aspiration as the EBBR sensors
received).  Measurements of aspirator flow were also recorded.  This
information was provided to the mentor.  The mentor then compared the field
checks with the data recorded by the EBBRs.

The periods of data and data fields that are incorrect because of the checks
are listed below.  Times are those at which the data are reported.


Data Fields
5 minute:  tair_top, tair_bot, thum_top, thum_bot, hum_top, hum_bot,
           vp_top, vp_bot
15 minute: rr_thum_r, rr_thum_l, mv_hum_r, mv_hum_l, tair_r, tair_l
30 minute: tair_top, tair_bot, thum_top, thum_bot, hum_top, hum_bot,
           vp_top, vp_bot, bowen, e, h

5 minute:  2005, 2010, 2015, 2020, 2025, 2030, 2035, 2040, 2045,
           2050, 2055, 2100, 2105
15 minute: 2015, 2045, 2100, 2115
30 minute: 2030, 2100

(EDITOR'S NOTE:  The following analysis refers to all EBBRs installed in Nov 1994)

Results of the T/RH comparisons:
The combined accuracy of the HMI31 and EBBR temperature sensors
(thermocouples or PRTDs) is +/- 0.4 degrees C.  The combined accuracy of the
HMI31 and EBBR RH sensors is +/- 4% for RH less than 80%, and +/- 6% for RH
greater than 80%.  The combined accuracy for each pair of EBBR sensors of
the same type is essentially the same as the quantities stated above.

All of the pairs of EBBR sensors show differences that fall within the
stated combined accuracies.  Although this sounds wonderful, a few of the
differences are close to the combined accuracy, which, because of the small
differences in temperature being measured (normally smaller than the
magnitude of the combined accuracy) could lead to some incorrect estimation
of sensible and latent heat flux.  However, unless there would be substantial
differences of calibration slope of two sensors in a pair, the switching of
height of the sensors every 15 minutes by the automatic exchange mechanism
will remove the offset between the sensors.

The comparisons between the EBBR sensors and the HMI31 T/RH meter showed
much larger differences.  The range of differences were: -2.4 to 0.0 degrees
for the thermocouples, -2.1 to 0.1 degrees for the RH probe PRTDs, and -6.6 to
6.7 percent for the RH sensors.  Six Thermocouples indicated differences from
the HMI31 greater than the combined accuracy.  Seven PRTDs indicated
differences from the HMI31 greater than the combined accuracy.  Four RH
sensors indicated differences from the HMI31 greater than the combined
accuracy.  The temperature differences (for both thermocouples and PRTDs)
were nearly all of one sign; the HMI31 indicated the greater temperature,
which may suggest a bias in the HMI31 temperature measurement, even though
a dozen differences of +/- 0.2 degrees were measured.  Four differences of
zero and only one positive difference (out of 40) were measured.  Thirteen of
the 20 RH differences were positive (HMI31 indicating the lower
RH), with the differences near the level of the combined accuracies being
approximately 50% positive and 50% negative.  It does not appear that the
HMI31 has a RH bias.

Plots of EBBR sensor/HMI31 differences as a function of time from the
installation of the individual sensors (a range of 10 to 30 months in the
field) shows no obvious pattern of sensor drift with time.  This is encouraging.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D020628.2
Start DateStart TimeEnd DateEnd Time
10/06/1995000010/06/19952359
Subject:
SGP/EBBR/E13 - 3-month Check
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During EBBR 3 month checks the Automatic Exchange Mechanism is disabled
(reflected by home signals near zero) so that the two aspirator units can be
placed at the same height.  The measurements during this period, at least,
do not produce correct outputs of bowen ratio (bowen), sensible heat flux (h),
or latent heat flux (e), nor do the air temperature and relative humidity
measurements indicate gradients.  Checks performed before or after the AEM
is disabled also lead to some incorrect data.

Time of the check is not known, so the entire day has been flagged as
suspect.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D020723.1
Start DateStart TimeEnd DateEnd Time
12/22/1995203012/22/19952130
Subject:
SGP/EBBR/E13 - Thermocouple out of range, data incorrect
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The left thermocouple temperature for 22 December was out of range
between 2030 and 2130 GMT, yielding incorrect values as listed below:

5 minute:  tair_top, tair_bot
15 minute: tair_l
30 minute:  tair_top, tair_bot, bowen, h, e
Measurements:sgp5ebbrE13.a0:
  • bottom air temperature(tair_bot)
  • top air temperature(tair_top)

sgp15ebbrE13.a1:
  • Left air temperature(tair_l)

sgp30ebbrE13.a1:
  • bottom air temperature(tair_bot)
  • top air temperature(tair_top)
  • latent heat flux(e)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)


Back To Table of Contents

DQRID : D930428.2
Start DateStart TimeEnd DateEnd Time
07/13/1993120107/13/19931202
Subject:
SGP/EBBR/E13 - incorrect home signal
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
EDITOR'S NOTE:  This DQR refers to data collected by the EBBR at E13 prior
to the begin date of regular ARM data.  At that time, the data streams which
contain the EBBR.E13 data were named 
      Dsgp15ebbr1.a0
      Dsgp30ebbr1.a1
      Dsgp5ebbr1.a0
These data are not readily available from the ARM archive, but can be
made available by special request.  The actual time range of the problem
described here is 921230.0000-930423.1200.



EBBR1, Central Facility reported incorrect home value signals from 30
December 1992 through 23 April 1993.  The home signals are used in the
calculation of fluxes by the CR10 data logger.  The fluxes for this period
are thus invalid as reported and must be recalculated from the archived 15
minute data.  The proper home signals are less than 35 for 30 minute home
signal and greater than 35 for 15 minute home signal.  Home signals were
the same value for 15 minute and 30 minute during the period of interest,
although they were not a constant value.  The chronology of the situation
is reported below.  On 7 April 1993 I noticed the problem in the A0 data.

On 30 December 1992, the automatic exchange mechanism (AEM) of the Central
Facility EBBR froze up with ice and stopped working (surmised from looking
at the EBBR1 data).  This caused a fuse to blow and stop the mechanism from
operating.  However, one channel of the CR10 data logger was apparently damaged
in the process.  The condition of the AEM only, was noticed on 4 January 1993
by site operations personnel.  The blown fuse was replaced, which started
the AEM working; but AEM home signal values between 30 Dec and 04 Jan were
around zero.  Home values remained around zero until at least January 8, 1993.
I have a gap in data archived at ANL between 8 and 15 January 1993, during
which I do not know quite what was happening.  On 11 January 1993 site
operations personnel found that the EBBR1 battery was run down and the EBBR
thus was not working.  A new battery was installed.  On 15 January the home
values were about 34.  I am assuming that they became 34 upon installation
of the new battery on 11 January.  Until at least 15 January the home signals
stayed around 34.  After that period the home signals became greater than
35 and generally were around 36.  Only occasionally (a few hours here and
there)were the home signals just above or below 35 to produce the proper
flux outputs.  On 23 April 1993, at my direction (and after a week of tests
on other parts of the system), the CR10 data logger was replaced.  This solved
the problem.  In fact, previous to this I had suggested reloading the software
into the previous CR10, but the CR10 would not accept it; as soon as the
machine was deactivated before that procedure it stopped working altogether.
I find it amazing that it worked at all, although all data other than the home
signals, and the calculated quantities dependent on them looked perfectly
acceptable during the period of interest; there is no evidence that the
CR10 was malfunctioning in other areas.

The road to restoring the 30 Dec to 23 April data would be a rocky one, as
each 15 minute data period would have to be examined to determine the
proper position of the sensors on the AEM.  However, it is possible to
reconstruct most of the 30 minute calculated values from the 15 minute data.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Time offset from base_time(base_time)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • Soil heat capacity 3(cs3)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • bottom relative humidity(hum_bot)
  • average surface soil heat flow at the surface(ave_shf)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • north latitude for all the input platforms.(lat)
  • Time offset from base_time(base_time)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • soil heat flow at the surface 3(g3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow, site 4(shf4)
  • Soil heat capacity 1(cs1)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • east longitude for all the input platforms.(lon)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D930503.2
Start DateStart TimeEnd DateEnd Time
07/13/1993120107/13/19931202
Subject:
SGP/EBBR/E13 - incorrect meteorological observations
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
EDITOR'S NOTE:  This DQR refers ti data collected by the EBBR at E13 prior
to the begin date of regular ARM data.  At that time, the data streams which
contain the EBBR.E13 data were named
      Dsgp15ebbr1.a0
      Dsgp30ebbr1.a1
      Dsgp5ebbr1.a0
These data are not readily available from the ARM archive, but can be 
made available by special request.  The actual time range of the problem
described here is 930417.1200-930422.1730.


Beginning at 1200 UTC on 17 April 1993, EBBR1, Central Facility, outputs
ramped to extreme values, some positive, some negative.  These outputs ended
their ramping approximately 3 hours later.  Comparison with SMOS data
indicate that no time averaged outputs from EBBR1 were consistent with the
SMOS after 1200 UTC.

It appears that the averaging instruction in the CR10 data logger had been
corrupted.  On 22 April site operations, at my request, tried to reenter
the software; this attempt was completely unsuccessful, indicating that the
CR10 probably had other problems as well.  EBBR1 was offline from 1730 UTC
on 22 April until 1400 UTC on 23 April, when a new CR10 was installed and the
software downloaded successfully.

Since a SDS utility for extracting real time data from the CF SMOS had not been
established, EBBR1 was being used for weather observations.  All EBBR1
measurements of meteorological quantities during the period above are
invalid.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Time offset from base_time(base_time)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • Soil heat capacity 3(cs3)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • bottom relative humidity(hum_bot)
  • average surface soil heat flow at the surface(ave_shf)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • north latitude for all the input platforms.(lat)
  • Time offset from base_time(base_time)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • soil heat flow at the surface 3(g3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow, site 4(shf4)
  • Soil heat capacity 1(cs1)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • east longitude for all the input platforms.(lon)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D931108.3
Start DateStart TimeEnd DateEnd Time
07/13/1993120011/02/19932121
Subject:
SGP/EBBR/E13 - pressure calibration
DataStreams:sgp30ebbrE13.a1
Description:
In the original Campbell CR10 software provided by the vendor (version 1),
the EBBR had incorrect calibration pressure sensor slopes and offsets.
The slopes and offset was carried through into version 2 of the
software and was not discovered by the mentor (me) until sometime later.
The calibration and slope did not deleteriously affect calculations in
the program since only a four percent reduction in atmospheric pressure
measurement resulted (the calculations are not very sensitive to small
errors in pressure). The vendor does not recall how the wrong
calibrations came to be used.   

Version 4 of the CR10 program includes the proper calibration and offset. 
This remedies the apparent offset problem (it was actually a calibration 
and offset problem). In comparisons with the co-located SMOS pressure
sensor, the difference between the SMOS and EBBR pressure values appeared
almost constant with time, hence the assumption of an offset problem.
However, the EBBR pressure sensor offsets are so large (a consequence of
tailoring the calibration curve to a small range of elevations in which the
calibration applies) that the very small error in slope was difficult to
recognize.

The outputted pressure values for the EBBR system can be corrected
with the following information and equations.  

         Old Slope     Old Offset        New Slope     New Offset

          0.01952        81.24            0.02031        81.27

   Correct Pressure =
               ((Current Pressure Data - 81.24)*0.02031/0.01952) + 81.27
                    =  1.04047*(Current Pressure Data) - 3.258
Measurements:sgp30ebbrE13.a1:
  • pressure at constant pressure surface(pres)


Back To Table of Contents

DQRID : D931108.4
Start DateStart TimeEnd DateEnd Time
07/13/1993120011/02/19932121
Subject:
SGP/EBBR/E13 - solid moisture correction
DataStreams:sgp30ebbrE13.a1
Description:
In the original EBBR software (Version 1) for the Campbell CR10 at the Central
Facility (E13), adjustment of the soil moisture for soil type was performed
differently than for the other EBBR systems.  This was supposed to have
been changed prior to installation (according to the vendor), but the
change was not made.  This adjustment was carried into Version 2 and was
not discovered by the mentor (me) until later.  A polynomial is used to
adjust the measured soil moisture for differences between the soil type at
the location of installation (clay-loam assumed) and the soil type (sand)
used in the calibration of the soil moisture sensor.  The adjustment in
the E13 EBBR only, was computed on the basis of a sandy-loam soil.

Presently, a clay-loam soil type is assumed for each EBBR location.  Soil
types at the extended facilities have not been characterized yet, although
there are hopes of doing so in the future.  The effect of using a
polynomial for sandy-loam soil instead of clay-loam soil is to decrease the
resultant soil moisture values by approximately 14.5% when the clay-loam
polynomial would indicate a soil moisture of 28.3%, and by approximately
38.3% when the clay-loam polynomial would indicate a soil moisture of 6.3%.
The normal range of soil moisture at the EBBR sites is approximately 3% to
35%.

The effect of the soil moisture decreases above on the adjustment to soil heat
flux plate measurements is less than 1.0%.  The effect on the change in
energy storage in the soil (determined from the change in soil temperature
over time) is a 10% decrease for a soil moisture of 28.3% and a decrease of
13.0% for a soil moisture of 6.3%.  The change in energy storage is typically
5% of the total surface energy budget during mid-day and 25% at night.
Therefore, the soil type adjustment error in the Central Facility EBBR
resulted in approximately a 0.5% error in the surface energy budget during
mid-day and 2.5% at night.  These are small and acceptable errors and
should not cause one to need to recalculate energy budget values.
Measurements:sgp30ebbrE13.a1:
  • Soil heat capacity 3(cs3)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • latent heat flux(e)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • Soil heat capacity 1(cs1)
  • average surface soil heat flow at the surface(ave_shf)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil heat capacity 5(cs5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • Soil heat capacity 2(cs2)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • corrected sensible heat flux(h)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)


Back To Table of Contents

DQRID : D940106.5
Start DateStart TimeEnd DateEnd Time
12/31/1993195012/31/19932100
Subject:
SGP/EBBR/E13 - Invalid data during disconnection of AEM at E13
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
On December 31, 1993 at 1950 GMT the AEM on the Central Facility EBBR was
disconnected.  Another AEM was then connected, on which some testing was needed
before site operations could be confident that it was ready for field
installation at an extended facility.  At 2041 GMT the original AEM was
reconnected.  The following 5, 15, and 30 minute data between or for the stated
times below is invalid:

5 minute (1950 to 2045 GMT): tair_top, tair_bot, thum_top, thum_bot, hum_top,
          hum_bot, vp_top, vp_bot, home

15 minute (2000 to 2045 GMT): rr_thum_r, rr_thum_l, mv_hum_r, mv_hum_l,
           mv_home, tair_r, tair_l

30 minute (2000 through 2100 GMT): tair_top, tair_bot, thum_top, thum_bot,
           hum_top, hum_bot, vp_top, vp_bot, bowen, e, h, home_15, home_30
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Right relative humidity(mv_hum_r)
  • Left relative humidity(mv_hum_l)
  • Home signal(mv_home)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)


Back To Table of Contents

DQRID : D940511.2
Start DateStart TimeEnd DateEnd Time
05/06/1994151505/06/19941600
Subject:
SGP/EBBR/E13 - SM4 Replacement
DataStreams:sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
Soil Moisture Probe #4 has been indicating large soil moistures in the past
couple of months.  At times the values have exceeded the upper limit of the
acceptable range.  This data could be considered questionable, although the
affect on average soil moisture and quantities affected by it is very small.
Therefore, I do not suggest additional flagging of the data other than that
imposed by the limits.  The probe was changed from S/N 92004 to 93004 on
May 6, 1994 at 1530 GMT.  During the exchange process a few selected periods
of soil moisture #4 data is incorrect, but not so different from the other
soil moisture probes as to have a significant affect on the average soil
moisture or the fluxes.

Additionally, the EBBR output was interrupted for a half hour while the
calibration of the new probe was entered into the CR10 data logger.
Therefore, all 5 minute data from 1535 to 1600 GMT, 15 minute data for 1545
and 1600 GMT, and 30 minute data for 1600 GMT is incorrect.

Furthermore, disturbance of the area near the #4 soil probes (temperature,
soil moisture, and heat flux) caused all three to be incorrect for the
following periods:

30 minute  1530 GMT

15 minute  1515 and 1530 GMT

5 minute   1515, 1520, 1525, and 1530 GMT.

Complete recovery by all three sensors did not occur for one day (which is
fairly typical for near surface installations), although the differences
from the other four sets of soil sensors did not deleteriously affect the
averages of the soil quantities.
Measurements:sgp15ebbrE13.a1:
  • Right air temperature(tair_r)
  • Soil heat flow 4(mv_hft4)
  • Left air temperature(tair_l)
  • Soil temperature 4(rr_ts4)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • 5 cm soil heat flow, site 4(shf4)
  • corrected sensible heat flux(h)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)


Back To Table of Contents

DQRID : D941021.5
Start DateStart TimeEnd DateEnd Time
10/13/1994230010/14/19941900
Subject:
SGP/EBBR/E13 - Soil Temperature Aberations
DataStreams:sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
For a period of not quite a day, soil temperature probe #4 indicated values
that were either too high or too low, for unknown reasons.  After Site
Operations personnel checked connectors and the probe itself, it recovered
to proper values.  The probe has functioned properly since then.  The times
and incorrect data fields are listed below.

15 minute: rr_ts4, 10/13/94: 2245 GMT; 10/14/94: 0000, 0200, 0230, 0515,
                  0600, 0630, 1300-1500, 1530-1715, 1815, 1845 GMT

30 minute: ts4, 10/13/94: 2300 GMT; 10/14/94: 0000, 0230, 0530-0630,
                  1300-1700, 1830-1900 GMT
           ces4, g4, ave_shf, e, h, 10/14/94: 0030, 0200-0230, 0600-0630,
                  1300-1900 GMT
Measurements:sgp15ebbrE13.a1:
  • Soil temperature 4(rr_ts4)

sgp30ebbrE13.a1:
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • 0-5 cm integrated soil temperature, site 4(ts4)


Back To Table of Contents

DQRID : D941208.1
Start DateStart TimeEnd DateEnd Time
12/02/1994193712/02/19942000
Subject:
SGP/EBBR/E13 - Net Radiation - Hemisphere Replacement
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The upper hemisphere of the net radiometer was punctured (pinhole) and thus
was replaced at 1937 GMT on December 2, 1994.  This resulted in a spike in
the net radiation data.  5 minute q data for 1935, 1940, 1945, and
1955 GMT, 15 minute mv_q data for 1945 and 2000 GMT, and 30 minute q, e,
and h data for 2000 GMT are incorrect.
Measurements:sgp5ebbrE13.a0:
  • specific humidity(q)

sgp15ebbrE13.a1:
  • Net radiation(mv_q)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • specific humidity(q)
  • corrected sensible heat flux(h)


Back To Table of Contents

DQRID : D950126.1
Start DateStart TimeEnd DateEnd Time
12/13/1994043012/13/19940500
12/13/1994180012/13/19941830
12/18/1994090012/18/19941030
12/18/1994163012/18/19941930
12/19/1994000012/19/19941600
12/20/1994020012/20/19940400
12/23/1994083012/23/19942030
12/24/1994080012/25/19940100
12/25/1994020012/25/19941400
12/25/1994150012/25/19941600
12/25/1994170012/26/19941800
12/27/1994020012/27/19941700
12/30/1994173012/30/19941800
Subject:
SGP/EBBR/E13 - Incorrect Soil Temperature #4
DataStreams:sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
For periods of a number of days in December 1994, soil temperature probe #4
indicated incorrect values that were either too high or too low.  Site
Operations personnel replaced the sensor on December 30, 1994.  The times
and incorrect data fields are listed below.  Only half hour times are
listed.  The incorrect data on December 30 was the result of the process of
replacing the sensor during that time.

Data Fields:
15 minute: rr_ts4
30 minute: ts4, ces4, g4, ave_shf, e, h

Dates and Times (GMT):
12/13/94  0500, 1830
12/18/94  0900-1030, 1630-1930
12/19/94  0000-1600
12/20/94  0200-0400
12/23/94  0830-2030
12/24/94  0800-2330
12/25/94  0000-0100, 0200-1400, 1530, 1600, 1700-2330
12/26/94  0000-1800
12/27/94  0200-1700
12/30/94  1730-1800

Recomputation of the change in energy storage in the soil could be done
roughly from the soil temperature sensors that were still working (roughly
because the difference in soil temperature with time is determined with
real-time (one minute samples) data, not from the 15 or 30 minute data).
However, this would require considerable effort.  The process for doing so
is therefore not stated here.  Contact the mentor for more information if
neccesary.
Measurements:sgp15ebbrE13.a1:
  • Soil temperature 4(rr_ts4)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • average surface soil heat flow at the surface(ave_shf)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 4(g4)
  • corrected sensible heat flux(h)
  • 0-5 cm integrated soil temperature, site 4(ts4)


Back To Table of Contents

DQRID : D950626.1
Start DateStart TimeEnd DateEnd Time
02/14/1995110002/14/19951730
Subject:
SGP/EBBR/E13 - Frozen Wind Speed Sensor
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
DQR No:                               Platform: EBBR

Subject: Frozen Wind Speed Sensor

Date Submitted: JUNE 22, 1995
Submitted By:                         _x_  Instrument Mentor
                                      ___  EST Member
                                      ___  Science Team Member
                                      ___  Other _____________________________

For questions or problems, please contact the ARM Experiment Center at
509-375-6898 or via email at dqr@arm.gov.

Platform/Measurement: EBBR/ Wind Speed
        What level data: (raw,a0,a1,b1,c1 etc): a1 (15 and 30 minute)
                                                a0 (5 minute)

    What location was the data collected at: E13, Central Facility

    Period of time in question
        Begin Date 2/14/95   Time 1100 GMT
        End                  Time 1730 GMT

 Data should be labeled:
 ___  questionable                      ___  All data fields affected
 _X_  incorrect                         _X_  Only some data fields affected
 ___  wrong calibration
 ___  others

 Discussion of Problem:

On February 14, 1995 a frontal system deposited freezing rain in central
Oklahoma that resulted in the EBBR wind speed instrument becoming frozen in
place at the Central Facillity (E13) for part of a day.  All 5, 15, and 30
minute data values indicated below are incorrect for the period listed above.

5 minute:  wind_s, res_ws
15 minute: wind_s
30 minute: wind_s, res_ws

Other observations/measurements impacted by this problem:

Suggested Corrections of the Problem: (e.g. change calibration factor and
recompute, flag data with this comment, etc.)

Flag data with this comment.

Data Processing Notes                Date

-------------------------------------------------------------------
END
Measurements:sgp5ebbrE13.a0:
  • Resultant wind speed(res_ws)
  • scalar wind speed(wind_s)

sgp15ebbrE13.a1:
  • scalar wind speed(wind_s)

sgp30ebbrE13.a1:
  • scalar wind speed(wind_s)
  • Resultant wind speed(res_ws)


Back To Table of Contents

DQRID : D950626.2
Start DateStart TimeEnd DateEnd Time
03/07/1995024503/08/19951640
Subject:
SGP/EBBR/E13 - Frozen Wind Speed Sensor
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
On March 7, 1995 freezing rain stopped the cups of the EBBR wind
speed instrument at the Central Facility (E13).  All 5, 15, and 30
minute data values indicated below are incorrect for the period listed above.

5 minute:  wind_s, res_ws
15 minute: wind_s
30 minute: wind_s, res_ws
Measurements:sgp5ebbrE13.a0:
  • Resultant wind speed(res_ws)
  • scalar wind speed(wind_s)

sgp15ebbrE13.a1:
  • scalar wind speed(wind_s)

sgp30ebbrE13.a1:
  • scalar wind speed(wind_s)
  • Resultant wind speed(res_ws)


Back To Table of Contents

DQRID : D950626.7
Start DateStart TimeEnd DateEnd Time
02/17/1995140002/22/19951500
Subject:
SGP/EBBR/E13 - Reprocess: Soil Temperature Malfunction
DataStreams:sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
For several days, soil temperature probe #4 indicated values
that were either too high or too low, for unknown reasons.  After Site
Operations personnel checked connections, it recovered to proper values.
Affected quantities are shown below.

15 minute: rr_ts4

30 minute: ts4, ces4, g4, ave_shf, e, h

Sensible, latent, and soil heat fluxes need to be recalculated using the
change in energy storage of probes 1-3 and 5, as follows.

ave_shf = (g1 + g2 + g3 + g5)/4

e = -(q + ave_shf)/(1 +bowen)

h = -(e + ave_shf +q)
Measurements:sgp15ebbrE13.a1:
  • Soil temperature 4(rr_ts4)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • average surface soil heat flow at the surface(ave_shf)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 4(g4)
  • corrected sensible heat flux(h)
  • 0-5 cm integrated soil temperature, site 4(ts4)


Back To Table of Contents

DQRID : D950815.2
Start DateStart TimeEnd DateEnd Time
08/01/1995150008/02/19951615
Subject:
SGP/EBBR/E13 - Low Battery Voltage and AEM Left on Manual
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
Low battery voltage caused some data values to be incorrect beginning at
1500 GMT on August 1, 1995.  The data should be carefully inspected to
determine which values are incorrect.

During replacement of the battery at the Central Facility EBBR on August
1, 1995, the AEM exchange toggle switch was left in the manual position,
which caused the right aspirator to remain in the home position until the
switch was correctly placed in the exchange position at 1616 GMT on August
2, 1995.  All 5, 15, and 30 minute values of temperature, relative humidity
, vapor pressure, bowen, e, and h are incorrect during the period. 15 and
30 minute values are also incorrect at 1630 GMT.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • top relative humidity(hum_top)
  • bottom vapor pressure(vp_bot)

sgp30ebbrE13.a1:
  • bottom air temperature(tair_bot)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)


Back To Table of Contents

DQRID : D950828.1
Start DateStart TimeEnd DateEnd Time
08/16/1995060008/16/19951530
08/18/1995123008/18/19951500
08/19/1995110008/19/19951500
08/20/1995090008/20/19951500
08/21/1995060008/21/19951500
Subject:
SGP/EBBR/E13 - Battery Voltage Drop
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
Sometime before August 16, 1995 the AC/DC converter was switched off and
the instrument heaters were switched on.  The solar panel was not able to
keep the battery voltage up under these conditions.  Much of the data for
the periods indicated is incorrect, especially data from the sensors that
require 12 volts DC power.  The data would have to be inspected to
determine what data is correct and what is incorrect.  It would be safest to
exclude all data from those periods from any analysis.  Site operations
switched the heaters off and turned the converter back on on August 21,
1995.

As reported in a recent DQR, the fluxes from the EBBR are incorrect
presently because of a malfunctioning T/RH probe; no spares are presently
available.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D951113.1
Start DateStart TimeEnd DateEnd Time
10/26/1995000011/03/19952045
Subject:
SGP/EBBR/E13 - Wind Direction Set Pin Slippage
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The set pin bolt on the wind vane loosened, allowing the vane to turn on
the shaft.  Wind directions are incorrect as a result, for the period
listed above.  The bolt was tightened on 3 Nov 95 so that correct wind
directions would result.

Values that are incorrect for the period are:

5 minute:   wind_d, res_ws, sigma_wd

15 minute:  mv_wind_d

30 minute:  wind_d, res_ws, sigma_wd
Measurements:sgp5ebbrE13.a0:
  • wind direction (relative to true north)(wind_d)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • Resultant wind speed(res_ws)

sgp15ebbrE13.a1:
  • Wind direction (relative to true north)(mv_wind_d)

sgp30ebbrE13.a1:
  • wind direction (relative to true north)(wind_d)
  • Resultant wind speed(res_ws)
  • standard deviation of wind direction (sigma theta)(sigma_wd)


Back To Table of Contents

DQRID : D951113.6
Start DateStart TimeEnd DateEnd Time
11/04/1995120011/04/19951400
11/05/1995033011/05/19951430
11/06/1995000011/06/19951530
11/07/1995000011/07/19951400
11/08/1995000011/08/19951400
Subject:
SGP/EBBR/E13 - Battery voltage drop
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
On Friday 2 November, 1995 the instrument heaters were switched on.  By
4 November, the solar panel was not able to maintain the battery voltage for
the cold night conditions that existed.  On Monday, 5 November the heaters
were turned off, but the poor condition of the battery did not allow it,
once partially drained, to recharge sufficiently for nighttime conditions.
On 8 November, at 2106 GMT, the battery was replaced (resulting in missing
data for 2030-2130 GMT).  Most of the data for the period above is incorrect,
especially data from the sensors that require at least 11 volts DC power.
The data that is incorrect is listed below.

5 minute:   tref, tair_top, tair_bot, thum_top, thum_bot, hum_top, hum_bot,
            vp_top, vp_bot, q, pres, home

15 minute:  rr_thum_r, rr_thum_l, rr_ts1, rr_ts2, rr_ts3, rr_ts4, rr_ts5,
            rr_tref, mv_hum_r, mv_hum_l, mv_pres, mv_home, mv_q, mv_hft1,
            mv_hft2, mv_hft3, mv_hft4, mv_hft5, tair_r, tair_l

30 minute:  tair_top, tair_bot, tref, thum_top, thum_bot, hum_top, hum_bot,
            vp_top, vp_bot, pres, home_15, home_30, bowen, e, h, shf, shf1,
            shf2, shf3, shf4, shf5, c_shf1, c_shf2, c_shf3, c_shf4, c_shf5,
            ts1, ts2, ts3, ts4, ts5, q, g1, g2, g3, g4, g5, ces1, ces2,
            ces3, ces4, ces5

Periods of time affected (these are the 30 minute periods that are
incorrect - incorrect 5 and 15 minute data may also occur for all or part
of the previous half hour):

4 Nov 95: 1200-1400 GMT
5 Nov 95: 0330-1430 GMT
6 Nov 95: 0000-1530 GMT
7 Nov 95: 0000-1400 GMT
8 Nov 95: 0000-1400 GMT
Measurements:sgp5ebbrE13.a0:
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • specific humidity(q)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • Soil heat flow 3(mv_hft3)
  • Soil heat flow 5(mv_hft5)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Left air temperature(tair_l)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • bottom relative humidity(hum_bot)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • soil heat flow at the surface 3(g3)
  • 5 cm soil heat flow, site 4(shf4)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D951116.1
Start DateStart TimeEnd DateEnd Time
11/11/1995070011/11/19950730
Subject:
SGP/EBBR/E13 - AEM Exchange Stopped in Snow and Freezing Rain
DataStreams:sgp30ebbrE13.a1
Description:
On the night of November 10-11, a north-south line from south central
Kansas through south central Oklahoma received snow and freezing rain and experienced
below freezing temperatures.  This caused the EBBR automatic exchange mechanism (AEM) to
stop exchanging temporarily.   

Note that temperatures, relative humidities, and vapor pressures are not affected; these
are correct as measured, but the height at which the measurements occurred must be
determined from the home signal value.
Measurements:sgp30ebbrE13.a1:
  • latent heat flux(e)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)


Back To Table of Contents

DQRID : D951220.2
Start DateStart TimeEnd DateEnd Time
12/05/1995181512/07/19951900
Subject:
SGP/EBBR/E13 - Missing data
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
The EBBR 13 data during the period indicated is missing.  This may be related
to the replacement of fiber optic cable at the Central Facility; this activity
was taking place at the time.  It is unknown whether the data was
sneakernetted for this missing period.  A PIF has been submitted concerning
the data loss, as provision was supposedly made to avoid any loss of data
during the fiber replacement.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Time offset from base_time(base_time)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • Soil heat capacity 3(cs3)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • bottom relative humidity(hum_bot)
  • average surface soil heat flow at the surface(ave_shf)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • north latitude for all the input platforms.(lat)
  • Time offset from base_time(base_time)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • soil heat flow at the surface 3(g3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow, site 4(shf4)
  • Soil heat capacity 1(cs1)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • east longitude for all the input platforms.(lon)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D951220.6
Start DateStart TimeEnd DateEnd Time
12/09/1995053012/09/19951415
12/13/1995040012/13/19951800
12/13/1995230012/14/19951430
12/15/1995074512/15/19951515
Subject:
SGP/EBBR/E13 - battery voltage drop
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The E13 battery condition was such that the solar panel was not able to
keep the battery voltage up (greater than 11 V DC) under cloudy conditions.
The data for the periods above is incorrect; many sensors require at least
11 volts DC power.  On 15 December 1995 at 1900 GMT the EBBR lost it's
connection to the site data system; data after this period will be discussed
in a separate DQR.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D960104.1
Start DateStart TimeEnd DateEnd Time
12/15/1995190012/21/19950405
12/21/1995163012/22/19952045
Subject:
SGP/EBBR/E13 - EBBR down - Data Missing
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
Between 15 and 22 December 1995 the E13 EBBR experienced a number of
communication and hardware problems.  The data for the periods indicated
are therefore missing.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Time offset from base_time(base_time)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • Soil heat capacity 3(cs3)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • bottom relative humidity(hum_bot)
  • average surface soil heat flow at the surface(ave_shf)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • north latitude for all the input platforms.(lat)
  • Time offset from base_time(base_time)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • soil heat flow at the surface 3(g3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow, site 4(shf4)
  • Soil heat capacity 1(cs1)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • east longitude for all the input platforms.(lon)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D960508.6
Start DateStart TimeEnd DateEnd Time
05/06/1996175505/06/19961835
Subject:
SGP/EBBR/E13 - 3-month check
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During EBBR 3 month checks the Automatic Exchange Mechanism is disabled
(reflected by home signals near zero) so that the two aspirator units can be
placed at the same height.  The measurements during this period, at least,
do not produce correct outputs of bowen ratio (bowen), sensible heat flux (h),
or latent heat flux (e), nor do the air temperature and relative humidity
measurements indicate gradients.  Checks performed before or after the AEM
is disabled also lead to some incorrect data.  The period of incorrect
data for the EBBR is listed above; data times affected do not include the
beginning time and do include the ending time (data files are denoted by
the end time).
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D960606.1
Start DateStart TimeEnd DateEnd Time
05/24/1996180005/24/19962130
Subject:
SGP/EBBR/E13 - Annual Calibration changeout
DataStreams:sgp5ebbrE13.a0, sgp30ebbrE13.a1
Description:
On May 24, 1996 the changeout for annual calibration occurred at E13,
Central Facility, OK.  Between 1800 and 2130 GMT no data was remotely collected.
Furthermore, 5 minute data inbetween 1800 and 2130 is incorrect, 15 minute data 
between 1800 and 2130 is incorrect, and 30 minute data for 2130 GMT is 
incorrect.  A large jump in soil moisture appears in the data after the 
installation was completed (the soil bags holding the probes had a greater 
than ambient soil moisture).  Soil measurements indicated greater than ambient 
soil moisture until a rain just after 0600 GMT on 1 June saturated the soil; 
after this period the probes reflected actual soil moisture conditions.  

The larger than normal soil moistures have some impact on the soil heat flux 
during this time of year, and thus soil heat flux from the soil flow plates 
and soil temperature probes, as well as average soil heat flux, computed 
sensible and latent heat fluxes; these quantities should be considered to 
be incorrect from 24 June at 2130 GMT until about 1200 GMT on June 1.

Because of communication problems, data is missing from the time of the 
EBBR installation until 29 May 1996 at about 1815 GMT.  This data may be 
recovered from the sneakernetted data set.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • Home signal(home)
  • pressure at constant pressure surface(pres)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Time offset from base_time(base_time)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • Soil heat capacity 3(cs3)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • bottom relative humidity(hum_bot)
  • average surface soil heat flow at the surface(ave_shf)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • north latitude for all the input platforms.(lat)
  • Time offset from base_time(base_time)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • soil heat flow at the surface 3(g3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow, site 4(shf4)
  • Soil heat capacity 1(cs1)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • soil heat flow at the surface 2(g2)
  • bottom vapor pressure(vp_bot)
  • east longitude for all the input platforms.(lon)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • top relative humidity(hum_top)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D961122.11
Start DateStart TimeEnd DateEnd Time
08/20/1996070008/30/19961830
Subject:
SGP/EBBR/E13 - Wind Direction Incorrect
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
Wind direction was incorrect during the period indicated due to a sensor 
electronics failure.  On 30 August 1996 site operations replaced S/N K3035
with S/N K3034.  Correct data collection resumed.

Values that are incorrect for the period are:

5 minute:   wind_d, res_ws, sigma_wd

15 minute:  mv_wind_d

30 minute:  wind_d, res_ws, sigma_wd
Measurements:sgp5ebbrE13.a0:
  • wind direction (relative to true north)(wind_d)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • Resultant wind speed(res_ws)

sgp15ebbrE13.a1:
  • Wind direction (relative to true north)(mv_wind_d)

sgp30ebbrE13.a1:
  • wind direction (relative to true north)(wind_d)
  • Resultant wind speed(res_ws)
  • standard deviation of wind direction (sigma theta)(sigma_wd)


Back To Table of Contents

DQRID : D961122.24
Start DateStart TimeEnd DateEnd Time
11/18/1996194211/18/19962022
Subject:
SGP/EBBR/E13 - EBBR 3 Month Checks - 10 EFs
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During EBBR 3 month checks the Automatic Exchange Mechanism is disabled 
(reflected by home signals near zero) so that the two aspirator units
can be placed at the same height.  The measurements during these periods 
do not produce correct outputs of bowen ratio (bowen), sensible heat flux (h), 
or latent heat flux (e), nor do the air temperature and relative humidity 
measurements indicate correct gradients.  Checks performed before or after the 
AEM is disabled also lead to some incorrect data.  Incorrect 5, 15 minute and 
half hour data occurs for periods indicated.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D970330.1
Start DateStart TimeEnd DateEnd Time
02/07/1997053002/07/19971340
Subject:
SGP/EBBR/E13 - Frozen Wind Speed Sensor
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
On February 7, 1997 freezing rain stopped the cups of the EBBR wind 
speed instrument at the Central Facility (E13).  All 5, 15, and 30 
minute data values indicated below are incorrect for the period listed.

5 minute:  wind_s, res_ws
15 minute: wind_s
30 minute: wind_s, res_ws
Measurements:sgp5ebbrE13.a0:
  • Resultant wind speed(res_ws)
  • scalar wind speed(wind_s)

sgp15ebbrE13.a1:
  • scalar wind speed(wind_s)

sgp30ebbrE13.a1:
  • scalar wind speed(wind_s)
  • Resultant wind speed(res_ws)


Back To Table of Contents

DQRID : D970730.3
Start DateStart TimeEnd DateEnd Time
07/17/1997093007/25/19971600
Subject:
SGP/EBBR/E13 - CR10 Malfunction
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The CR10 apparently malfunctioned on 17 July 1997.  This caused a variety 
of effects, including incorrect datalogger clock times, missing data 
periods, and some corrupted data fields.  The CR10 was replaced on 
25 July 1997; all data fields are now correct.  Data users may contact
the mentor for more detailed information on data quality during this 
period.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D971017.5
Start DateStart TimeEnd DateEnd Time
07/22/1997000007/22/19972359
07/23/1997000007/23/19972359
07/24/1997000007/24/19972359
Subject:
SGP/EBBR/E13 - Missing Data
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The EBBR EF13 data during the periods indicated are missing.  This may be related
to a CR10X clock problem that was observed at the time by the SDS.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • altitude above sea levelaltunits(alt)
  • pressure at constant pressure surface(pres)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • north latitude for all the input platforms.(lat)
  • bottom vapor pressure(vp_bot)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • scalar wind speed(wind_s)
  • east longitude for all the input platforms.(lon)
  • wind direction (relative to true north)(wind_d)
  • specific humidity(q)
  • Home signal(home)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • top air temperature(tair_top)
  • Reference Thermistor Temperature(tref)
  • Time offset from base_time(base_time)

sgp15ebbrE13.a1:
  • Soil temperature 1(rr_ts1)
  • altitude above sea levelaltunits(alt)
  • Soil heat flow 3(mv_hft3)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Soil temperature 2(rr_ts2)
  • Soil temperature 3(rr_ts3)
  • east longitude for all the input platforms.(lon)
  • Soil moisture 3(r_sm3)
  • Soil moisture 2(r_sm2)
  • Soil temperature 4(rr_ts4)
  • Soil heat flow 2(mv_hft2)
  • Right air temperature(tair_r)
  • Atmospheric pressure(mv_pres)
  • Battery(bat)
  • north latitude for all the input platforms.(lat)
  • Soil heat flow 5(mv_hft5)
  • Soil temperature 5(rr_ts5)
  • Left relative humidity(mv_hum_l)
  • Reference temperature(rr_tref)
  • Time offset of tweaks from base_time(time_offset)
  • Time offset from base_time(base_time)
  • Wind direction (relative to true north)(mv_wind_d)
  • Soil moisture 1(r_sm1)
  • scalar wind speed(wind_s)
  • Soil heat flow 1(mv_hft1)
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Soil heat flow 4(mv_hft4)
  • Signature(signature)
  • Left air temperature(tair_l)
  • Soil moisture 5(r_sm5)
  • Right relative humidity(mv_hum_r)
  • Net radiation(mv_q)
  • Home signal(mv_home)
  • Soil moisture 4(r_sm4)

sgp30ebbrE13.a1:
  • soil heat flow at the surface 1(g1)
  • Reference Thermistor Temperature(tref)
  • 0-5 cm integrated soil temperature, site 2(ts2)
  • latent heat flux(e)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • 5 cm soil heat flow, site 3(shf3)
  • average surface soil heat flow at the surface(ave_shf)
  • bottom relative humidity(hum_bot)
  • bottom air temperature(tair_bot)
  • soil heat flow at the surface 5(g5)
  • north latitude for all the input platforms.(lat)
  • standard deviation of wind direction (sigma theta)(sigma_wd)
  • 5 cm soil heat flow, site 4(shf4)
  • soil heat flow at the surface 3(g3)
  • Soil heat capacity 1(cs1)
  • Exchange mechanism position indicator (0 to 15 min)(home_15)
  • 5 cm soil heat flow, site 5(shf5)
  • 0-5 cm change in soil heat storage with time, site 5(ces5)
  • wind direction (relative to true north)(wind_d)
  • 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
  • 0-5 cm integrated soil temperature, site 3(ts3)
  • 0-5 cm integrated soil temperature, site 5(ts5)
  • specific humidity(q)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • temperature of the top humidity sensor chamber(thum_top)
  • altitude above sea levelaltunits(alt)
  • soil heat flow at the surface 2(g2)
  • top air temperature(tair_top)
  • 0-5 cm integrated soil temperature, site 2(ts1)
  • Soil moisture 5 (mass water/mass dry soil)(sm5)
  • Soil heat capacity 3(cs3)
  • top vapor pressure(vp_top)
  • Resultant wind speed(res_ws)
  • Exchange mechanism position indicator (15 to 30 min)(home_30)
  • Soil moisture 4 (mass water/mass dry soil)(sm4)
  • Soil heat capacity 4(cs4)
  • Time offset of tweaks from base_time(time_offset)
  • Soil heat capacity 5(cs5)
  • Soil heat capacity 2(cs2)
  • pressure at constant pressure surface(pres)
  • corrected sensible heat flux(h)
  • 0-5 cm change in soil heat storage with time, site 2(ces2)
  • Time offset from base_time(base_time)
  • 0-5 cm integrated soil temperature, site 4(ts4)
  • Soil moisture 3 (mass water/mass dry soil)(sm3)
  • 0-5 cm change in soil heat storage with time, site 3(ces3)
  • 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
  • Soil moisture 2 (mass water/mass dry soil)(sm2)
  • 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
  • scalar wind speed(wind_s)
  • 5 cm soil heat flow, site 1(shf1)
  • Soil moisture 1 (mass water/mass dry soil)(sm1)
  • 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
  • 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
  • 5 cm soil heat flow, site 2(shf2)
  • 0-5 cm change in soil heat storage with time, site 2(ces1)
  • 0-5 cm change in soil heat storage with time, site 4(ces4)
  • east longitude for all the input platforms.(lon)
  • bottom vapor pressure(vp_bot)
  • top relative humidity(hum_top)
  • soil heat flow at the surface 4(g4)


Back To Table of Contents

DQRID : D971021.5
Start DateStart TimeEnd DateEnd Time
04/28/1997141904/28/19971445
Subject:
SGP/EBBR/E13 - EBBR Biannual Checks
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During EBBR 3 month checks the Automatic Exchange Mechanism is disabled 
(reflected by home signals near zero) so that the two aspirator units
can be placed at the same height.  The measurements during these periods 
do not produce correct outputs of bowen ratio (bowen), sensible heat flux (h), 
or latent heat flux (e), nor do the air temperature and relative humidity 
measurements indicate correct gradients.  Checks performed before or after the 
AEM is disabled also lead to some incorrect data.  Incorrect 5, 15 minute and 
half hour data occurs for periods indicated.
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D980117.19
Start DateStart TimeEnd DateEnd Time
01/04/1998062501/05/19980115
Subject:
SGP/EBBR/E13- EBBR Frozen Wind Speed
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
Wind speed cups were frozen during the indicated time periods. All 5,
15, and 30 minute data values indicated  are incorrect for the periods
listed.
Measurements:sgp5ebbrE13.a0:
  • Resultant wind speed(res_ws)
  • scalar wind speed(wind_s)

sgp15ebbrE13.a1:
  • scalar wind speed(wind_s)

sgp30ebbrE13.a1:
  • scalar wind speed(wind_s)
  • Resultant wind speed(res_ws)


Back To Table of Contents

DQRID : D980117.27
Start DateStart TimeEnd DateEnd Time
01/04/1998074501/16/19981600
Subject:
SGP/EBBR/E13 - EBBR AEMs Not Exchanging (Iced Or Fuse Blown)
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
The EBBR AEM stopped exchanging because of icing at during this time
period.

The calculations of Bowen ratio, latent heat flux, and sensible heat
flux are incorrect for the time period indicated.  The other
measurements listed  are also incorrect for those times:

Note: Mentor supplied the end date/time for this DQR after submittal
Measurements:sgp5ebbrE13.a0:
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Right relative humidity(mv_hum_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents

DQRID : D980416.12
Start DateStart TimeEnd DateEnd Time
10/10/1997185010/10/19971932
Subject:
SGP/EBBR/E13 - 3-Month Check
DataStreams:sgp5ebbrE13.a0, sgp15ebbrE13.a1, sgp30ebbrE13.a1
Description:
During EBBR 3 month checks the Automatic Exchange Mechanism is disabled
(reflected by home signals near zero) so that the two aspirator units can be
placed at the same height.  The measurements during these periods 
do not produce correct outputs of bowen ratio (bowen), sensible heat flux
(h), or latent heat flux (e), nor do the air temperature and relative 
humidity measurements indicate correct gradients.  Checks performed before 
or after the AEM is disabled also lead to some incorrect data.  Incorrect 5,
15 minute and half hour data occurs for the period above.
Measurements:sgp5ebbrE13.a0:
  • Time offset of tweaks from base_time(time_offset)
  • temperature of the top humidity sensor chamber(thum_top)
  • top air temperature(tair_top)
  • bottom relative humidity(hum_bot)
  • top relative humidity(hum_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom air temperature(tair_bot)
  • top vapor pressure(vp_top)
  • bottom vapor pressure(vp_bot)

sgp15ebbrE13.a1:
  • Temperature of left humidity sensor chamber(rr_thum_l)
  • Left air temperature(tair_l)
  • Right air temperature(tair_r)
  • Temperature of right humidity sensor chamber(rr_thum_r)
  • Right relative humidity(mv_hum_r)
  • Left relative humidity(mv_hum_l)

sgp30ebbrE13.a1:
  • wind direction (relative to true north)(wind_d)
  • scalar wind speed(wind_s)
  • latent heat flux(e)
  • top vapor pressure(vp_top)
  • temperature of the bottom humidity sensor chamber(thum_bot)
  • bottom relative humidity(hum_bot)
  • ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
  • corrected sensible heat flux(h)
  • temperature of the top humidity sensor chamber(thum_top)
  • bottom air temperature(tair_bot)
  • bottom vapor pressure(vp_bot)
  • top air temperature(tair_top)
  • top relative humidity(hum_top)


Back To Table of Contents



END OF DATA