TWP/SMET/C3 - Upper wind sensor failure

A lightning strike destroyed the upper (#1) wind sensor.

• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #1 direction standard deviation(wind1_dir_sd)

TWP/SMET/C3 - RH Values Artificially High

Lightning strike caused RH readings to be higher than reasonable (130%).

• Vapor pressure standard deviation(vappress_sd)
• Mean Relative Humidity(relh_mean)
• Relative humidity maximum(relh_max)
• Vapor pressure mean(vappress_mean)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)

TWP/SMET/C3 - Instrument failure

A lightning strike caused a failure in the ORG.  Rainfall was being continually recorded.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - ORG data noisy due to degraded ground

SMET Rain Data began to be noisy during December 2005 and the problem slowly became worse 
over time so that in February 2006 the ORG was reporting with a constant background value 
of around 0.10 mm/hr rain rate.  ORG voltage showed a near constant value above the 85mV 
threshold.  The ground for the ORG had become degraded and was lost due to corrosion.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Reprocess: Windspeed2 calibration error

The lower anemometer was replaced afer being removed in anticipation of cyclone Monica. 
The calibration coefficient was not changed during this period so the wind speeds are a 
little low (0.2%).

• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed standard deviation(wind2_spd_sd)

TWP/SMET/C3 - Anemometer Readings Incorrect

The Anemometer readings were incorrect due to the tower being lowered for maintenance.

• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 speed standard deviation(wind2_spd_sd)

TWP/SMET/C3 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the SMET suite of instruments effective 20060926. 
 Two new variables (count and rain amount) were added at the end of the twpsmet60sC1.b1 
datastream.  When reprocessing of this datastream occurs these variables will be added 
with -9999 (missing) as the value for dates prior to gauge installation.

• base time(base_time)

TWP/SMET/C3 - Barometer Data Incorrect

The barometer data was incorrect or missing due to water intrusion.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Data Incorrect Due to Water Intrusion

Data became erratic and unreasonable after water intrusion into the enclosure.

• Vapor pressure standard deviation(vappress_sd)
• Precipitation maximum(precip_max)
• Relative humidity maximum(relh_max)
• Mean Relative Humidity(relh_mean)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)
• precipitation minimum(precip_min)
• Precipitation mean(precip_mean)
• Temperature minimum(temp_min)
• Mean Air Temperature or Hardware Error(temp_mean)
• Temperature maximum(temp_max)
• Precipitation standard deviation(precip_sd)
• Vapor pressure mean(vappress_mean)
• Std Dev of Air Temperature(temp_sd)