TWP/SMET/C1 - C1 TWP  Wind speed calibration factor problem/ Wind1

Wind speed calibration factors were reversed between wind speed sensor 1 and 2.
Results in less than 1% error, but correction factors may be used.

• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #1 speed minimum(wind1_spd_min)

• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)

TWP/SMET/C1 - C1 SMET Incorrect wind speed calibration factors

Wind speed calibration factors were reversed between wind speed sensors 1 and 2.  Error 
results in less than a 1% error in wind speed.  A correction factor may be used.

• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #2 speed standard deviation(wind2_spd_sd)

• Wind #2 speed minimum(wind2_spd_min)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed standard deviation(wind2_spd_sd)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed maximum gust(wind2_spd_max_gust)

TWP/C1 - Incorrect elevation reported in Manus Data

(From Bill Clements) We have been using 6m MSL as the station
elevation of Momote (Manus).  This was based on information
posted near the station barometer in the Momote Weather Service
Office.  It turns out that the official WMO station elevation
for Momote is 4m MSL and the upper air elevation is 5m MSL.

All Manus instruments except the sonde station are at 4m MSL.
The sonde launching station is at 5m MSL.

• Dummy altitude for Zeb(alt)

• Dummy altitude for Zeb(alt)

• Dummy altitude for Zeb(alt)

• Dummy altitude for Zeb(alt)

• Dummy altitude for Zeb(alt)

TWP/SMET/C1 - Negative rainfall rates

Due to limitations of the Zeno dataloggers all voltage measurements
from the optical rain gauge (ORG) were converted to rainfall rates. 
This resulted in negative values for rain rates.  Any value below 0.10 mm/hr should be 
considered to be 0 mm/hr.  New dataloggers 
alleviated this problem.  New loggers were installed 03/09/2004 @ 2243 GMT.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C1 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C1 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the TWP.C1 SMET suite of instruments on 20061017. 
 Effective 20060926, two new variables (count and rain amount) were added to the end of 
the twpsmet60sC1.b1 datastream.  Between 9/26 and 10/17, the data for these two variables 
are filled with zeros.  Users should not use the data during this period as the zeros 
are not representative of the rain fall at the site.  When reprocessing of this datastream 
occurs these variables will be added for the 19961009-20060926 and data from 
19961009-20061017 will be filled with -9999 (missing).

• base time(base_time)