TWP/SMET/C3 - ORG data noisy due to degraded ground

SMET Rain Data began to be noisy during December 2005 and the problem slowly became worse 
over time so that in February 2006 the ORG was reporting with a constant background value 
of around 0.10 mm/hr rain rate.  ORG voltage showed a near constant value above the 85mV 
threshold.  The ground for the ORG had become degraded and was lost due to corrosion.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C1 - Upper wind speed sensor failure

The upper wind speed sensor was binding at low wind speeds.  Comparison to the lower wind 
sensor showed that the upper sensor flat-lines for long periods of time.  The upper 
anemometer was replaced.

• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #1 speed minimum(wind1_spd_min)

TWP/SMET/C2 - Temp/RH probe failure

Temperature/RH probe failed and was replaced.

• Mean Relative Humidity(relh_mean)
• Mean Air Temperature or Hardware Error(temp_mean)
• Relative humidity maximum(relh_max)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Std Dev of Air Temperature(temp_sd)
• Temperature minimum(temp_min)
• Relative humidity minimum(relh_min)
• Vapor pressure standard deviation(vappress_sd)
• Temperature maximum(temp_max)
• Vapor pressure mean(vappress_mean)

TWP/SMET/C3 - Anemometer Readings Incorrect

The Anemometer readings were incorrect due to the tower being lowered for maintenance.

• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 speed standard deviation(wind2_spd_sd)

TWP/SMET/C1 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C2 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C1 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the TWP.C1 SMET suite of instruments on 20061017. 
 Effective 20060926, two new variables (count and rain amount) were added to the end of 
the twpsmet60sC1.b1 datastream.  Between 9/26 and 10/17, the data for these two variables 
are filled with zeros.  Users should not use the data during this period as the zeros 
are not representative of the rain fall at the site.  When reprocessing of this datastream 
occurs these variables will be added for the 19961009-20060926 and data from 
19961009-20061017 will be filled with -9999 (missing).

• base time(base_time)

TWP/SMET/C2 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the TWP.C2 SMET suite of instruments on 20061129. 
Effective 20060926, two new variables (count and rain amount) were added to the end of 
the twpsmet60sC2.b1 datastream.  Between 9/26 and 11/29, the data for these two variables 
are filled with zeros.  Users should not use the data during this period as the zeros are 
not representative of the rain fall at the site.  When reprocessing of this datastream 
occurs these variables will be added for the 19981021-20060926 and data from 
19981021-20061129 will be filled with -9999 (missing).

• base time(base_time)

TWP/SMET/C3 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the SMET suite of instruments effective 20060926. 
 Two new variables (count and rain amount) were added at the end of the twpsmet60sC1.b1 
datastream.  When reprocessing of this datastream occurs these variables will be added 
with -9999 (missing) as the value for dates prior to gauge installation.

• base time(base_time)

TWP/SMET/C3 - Barometer Data Incorrect

The barometer data was incorrect or missing due to water intrusion.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Data Incorrect Due to Water Intrusion

Data became erratic and unreasonable after water intrusion into the enclosure.

• Vapor pressure standard deviation(vappress_sd)
• Precipitation maximum(precip_max)
• Relative humidity maximum(relh_max)
• Mean Relative Humidity(relh_mean)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)
• precipitation minimum(precip_min)
• Precipitation mean(precip_mean)
• Temperature minimum(temp_min)
• Mean Air Temperature or Hardware Error(temp_mean)
• Temperature maximum(temp_max)
• Precipitation standard deviation(precip_sd)
• Vapor pressure mean(vappress_mean)
• Std Dev of Air Temperature(temp_sd)

TWP/SMET/C1 - Upper winds failure

The upper wind instrument was inoperative resulting in constant wind direction and speed.  
A failed cable was replaced.

• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #1 speed minimum(wind1_spd_min)

TWP/SMET/C2 - Lower windspeed sensor questionable

Lower wind speed sensor had degraded bearings.  This sensor was reporting as much as 0.4 
m/s lower values than the upper sensors when the winds were 2 m/s or below.  The sensor 
was replaced.

• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #2 speed standard deviation(wind2_spd_sd)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed minimum(wind2_spd_min)

TWP/SMET/C3 - Upper wind speed artificially slow

The upper wind measurement was consistently slower by around 0.5 - 1 m/s than the lower 
wind measurement.  The bearings on the upper wind measurement were binding.

• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed vector average(wind1_spd_vec_avg)