Description: | June 8,2000 hard drive failure resulted in no data being collected or logged until hard
drive was replaced on July 18,2000. However, a control file in the replacement drive did
not forward the data. This control file was corrected and data flow was begun in August. |
Measurements: | sgpgaeriprofB1.c1: - Array of heights for the range gates(height)
- Initial surface dewpoint temperature used in retrieval(init_dewpointTemperature)
- Flag indicating aeri retrieval status(status_flag)
- Flag indicating where the initial surface water measurements are from: 0-> SMOS,
1-> AERI(water_flag) - Initial surface absolute temperature used in retrieval(init_temperature)
- Cloud base height(cloudBaseHeight)
- Interpolated dewpoint temperature(dewpointTemperature)
- Dummy altitude for Zeb(alt)
- Total precipitable water vapor, from Microwave Radiometer(totalPrecipitalWater)
- lat(lat)
- base time(base_time)
- Initial surface pressure used in retrieval(init_pressure)
- Time offset of tweaks from base_time(time_offset)
- lon(lon)
- atmospheric pressure at mean sea level and at tropopause (NGM250 predicted)(pressure)
- Interpolated water vapor mixing ratio(waterVaporMixingRatio)
- Flag indicating which instruments were available and provided input for the
retrieval(input_flag) - air temperature (NGM250 predicted)(temperature)
- Initial water vapor mixing ratio used in retrieval(init_waterVaporMixingRatio)
sgpaerisummaryB1.a1: - Wave number in reciprocal centimeters(wnumsum9)
- Logical flag indicating whether HBB temperature is stable (true) or not stable
(false). Determined using HBBtempDrift and HBBtempDriftLimit.(HBBstable) - Wave number in reciprocal centimeters(wnumsum14)
- Wave number in reciprocal centimeters(wnumsum6)
- Wave number in reciprocal centimeters(wnumsum7)
- Wave number in reciprocal centimeters(wnumsum11)
- Wave number in reciprocal centimeters(wnumsum8)
- Maximum departure from ideal of the mirror position over the course of all
contributing views. Typically two hot, two ambient, and one scene view are examine(sceneMirPosEncoderMaxDrift) - Wave number in reciprocal centimeters(wnumsum10)
- Wave number in reciprocal centimeters(wnumsum5)
- Shortwave window brightness temperature from radiance average (2510_2515 cm-1)(shortwaveWindowAirTemp2510_2515)
- Version number of Operational Software(systemReleaseNumber)
- Wave number in reciprocal centimeters(wnumsum2)
- Logical flag indicating that a data record is missing (true/false(missingDataFlag)
- AERI LW Scene Brightness Temp Spectral Averages (Ch1)(SkyBrightnessTempSpectralAveragesCh1)
- AERI SW Responsivity Spectral Averages (Ch2)(ResponsivitySpectraAveragesCh2)
- Logical flag indicating whether hatch is open (true) or not open (false)(hatchOpen)
- Cold blackbody temperature used in calibration(calibrationCBBtemp)
- Observation relative humidity at AERI blackbodies(atmosphericRelativeHumidity)
- Logical flag indicating whether shortwave channel noise equivalent radiance is
acceptable in sky view (true/false). Determined using SWskyNEN and SWskyNENlimit.(SWskyNENacceptable) - Observation atmospheric pressure in AERI electronics(atmosphericPressure)
- Longwave radiance average (700_705 cm-1) Elevated Air(elevatedLayerRadiance700_705)
- AERI LW Scene NESR Spectral Averages (Ch1)(SkyNENCh1)
- base time(base_time)
- Logical flag indicating whether longwave channel noise equivalent radiance is
acceptable in sky view (true/false). Determined using LWskyNEN and LWskyNENlimit.(LWskyNENacceptable) - AERI instrument unit serial number(AERIunitNumber)
- Radiance standard deviation during sky view averaged over (985_990 cm-1)(skyViewStdDevRadiance985_990)
- AERI instrument data channel number(channelNumber)
- Radiance standard deviation during sky view averaged over (2295_2300 cm-1)(skyViewStdDevRadiance2295_2300)
- AERI SW HBB 2min NESR Estimate #2 derived from sequential HBB views (Ch2)(HBB2minNENEstimateNo2Ch2)
- Shortwave elevated air brightness temperature from radiance average (2282_2287
cm-1)(elevatedLayerAirTemp2282_2287) - Radiance standard deviation during sky view averaged over (2282_2287 cm-1)(skyViewStdDevRadiance2282_2287)
- AERI LW HBB 2min NESR Estimate #2 derived from sequential HBB views (Ch1)(HBB2minNENEstimateNo2Ch1)
- Character string containing instrument name(instrumentUnitNumber)
- Time (HHMMSS)(timeHHMMSS)
- Difference between frontEndFanAirHeatedTemp and frontEndFanAirUnheatedTemp
indicative of front end air flow.(frontEndFanAirTempDiff) - AERI LW Scene Variability Spectral Averages (Ch1)(SkyVariabilityAveragesCh1)
- Maximum Temperature Difference Between ABB Thermistors(ABBmaxTempDiff)
- Ambient temperature used in calibration(calibrationAmbientTemp)
- AERI SW Scene Variability Spectral Averages (Ch2)(SkyVariabilityAveragesCh2)
- AERI LW Responsivity Spectral Averages (Ch1)(ResponsivitySpectraAveragesCh1)
- Longwave elevated air brightness temperature from radiance average (700_705
cm-1)(elevatedLayerAirTemp700_705) - Shortwave surface air brightness temperature from radiance average (2295_2300
cm-1)(surfaceLayerAirTemp2295_2300) - Rain sensor analog output: the rain sensor is located inside the hatch near the
sky aperture and is used to flag the critical condition of rain falling on the AERI s(rainSensorIntensity) - Radiance standard deviation during sky view averaged over (700_705 cm-1)(skyViewStdDevRadiance700_705)
- Noise-equivalent Radiance in Hot Blackbody at 2500 cm-1(SW_HBB_NEN)
- Hot blackbody temperature used in calibration(calibrationHBBtemp)
- Observation Altitude(Altitude)
- AERI SW HBB 2min NESR Estimate #1 derived from variance during HBB view (Ch2)(HBB2minNENEstimateNo1Ch2)
- Type of scene that has been calibrated (ASCII character as float)(calibratedSceneID)
- Julian Day including day and fraction of day(JulianDay)
- Difference between actual and ideal motor encoder values for current view
indicative of quality of the mirror positioning.(sceneMirPosEncoderDrift) - Longwave surface air brightness temperature from radiance average (675_680 cm-1)(surfaceLayerAirTemp675_680)
- Shortwave window radiance average (2510_2515 cm-1)(shortwaveWindowRadiance2510_2515)
- The noise equivalent radiance observed in the shortwave channel during a sky
view at 2500 cm-1(SWskyNEN) - Duration of scene view(sceneViewDuration)
- AERI LW HBB 2min NESR Estimate #1 derived from variance during HBB view (Ch1)(HBB2minNENEstimateNo1Ch1)
- The noise equivalent radiance observed in the longwave channel during a sky view
at 1000 cm-1(LWskyNEN) - lon(lon)
- Maximum Standard Deviation in Thermistor Channels 0..7(maxSampleStdDev)
- Characteristic value representing overall shortwave channel responsivity(SWresponsivity)
- Observation longitude(Longitude)
- Maximum Temperature Difference Between HBB Thermistors(HBBmaxTempDiff)
- Shortwave radiance average (2295_2300 cm-1) Surface Air(surfaceLayerRadiance2295_2300)
- Observation date(dateYYMMDD)
- The maximum excursion of hot-blackbody temperature over 5 consecutive scenes,
centered on the sky view(HBBtempDrift) - Time offset of tweaks from base_time(time_offset)
- Characteristic value representing overall longwave channel responsivity(LWresponsivity)
- Longwave window radiance average (985_990 cm-1)(longwaveWindowRadiance985_990)
- Radiance standard deviation during sky view averaged over (675_680 cm-1)(skyViewStdDevRadiance675_680)
- AERI LW Scene Radiance Spectral Averages (Ch1)(SkyRadianceSpectraAveragesCh1)
- Shortwave radiance average (2282_2287 cm-1) Elevated Air(elevatedLayerRadiance2282_2287)
- Ambient air temperature at hatch opening(outsideAirTemp)
- Scene mirror view angle in non-negative degrees, measured clockwise looking into
interferometer window.(sceneMirrorAngle) - Noise-equivalent Radiance in Hot Blackbody at 1000 cm-1(LW_HBB_NEN)
- Observation latitude(Latitude)
- AERI SW Scene NESR Spectral Averages (Ch2)(SkyNENCh2)
- Radiance standard deviation during sky view averaged over (2510_2515 cm-1)(skyViewStdDevRadiance2510_2515)
- lat(lat)
- AERI SW Scene Brightness Temp Spectral Averages (Ch2)(SkyBrightnessTempSpectralAveragesCh2)
- Time at center of AERI sky observation period(Time)
- Wave number in reciprocal centimeters(wnumsum1)
- AERI SW Scene Radiance Spectral Averages (Ch2)(SkyRadianceSpectraAveragesCh2)
- Dummy altitude for Zeb(alt)
- xxx(dataAvailable)
- Wave number in reciprocal centimeters(wnumsum12)
- Wave number in reciprocal centimeters(wnumsum13)
- Longwave window brightness temperature from radiance average (985_990 cm-1)(longwaveWindowAirTemp985_990)
- Longwave radiance average (675-680 cm-1) Surface Air(surfaceLayerRadiance675_680)
- Wave number in reciprocal centimeters(wnumsum3)
- Wave number in reciprocal centimeters(wnumsum4)
sgpaerich1B1.a1: - Observation longitude(Longitude)
- Observation Altitude(Altitude)
- Observation latitude(Latitude)
- Observation relative humidity at AERI blackbodies(atmosphericRelativeHumidity)
- Observation atmospheric pressure in AERI electronics(atmosphericPressure)
- Time offset of tweaks from base_time(time_offset)
- Maximum departure from ideal of the mirror position over the course of all
contributing views. Typically two hot, two ambient, and one scene view are examine(sceneMirPosEncoderMaxDrift) - base time(base_time)
- Ambient temperature used in calibration(calibrationAmbientTemp)
- Wave number(wnum)
- Time at center of AERI sky observation period(Time)
- Standard deviation of radiance spectra ensemble(standard_dev_mean_rad)
- BB Support Structure Temperature(BBsupportStructureTemp)
- Scene mirror view angle in non-negative degrees, measured clockwise looking into
interferometer window.(sceneMirrorAngle) - Duration of scene view(sceneViewDuration)
- Dummy altitude for Zeb(alt)
- Version number of Operational Software(systemReleaseNumber)
- wavenumbers for standard deviation of radiance spectra(wnum2)
- Character string containing instrument name(instrumentUnitNumber)
- Ambient air temperature at hatch opening(outsideAirTemp)
- Logical flag indicating that a data record is missing (true/false(missingDataFlag)
- AERI instrument unit serial number(AERIunitNumber)
- lat(lat)
- Observation date(dateYYMMDD)
- Cold blackbody temperature used in calibration(calibrationCBBtemp)
- Type of scene that has been calibrated (ASCII character as float)(calibratedSceneID)
- AERI instrument data channel number(channelNumber)
- Mean of radiance spectra ensemble(mean_rad)
- Hot blackbody temperature used in calibration(calibrationHBBtemp)
- Logical flag indicating whether hatch is open (true) or not open (false)(hatchOpen)
- lon(lon)
- Time (HHMMSS)(timeHHMMSS)
- Julian Day including day and fraction of day(JulianDay)
sgpaeriengineerB1.a1: - Imaginary radiance during sky view averaged over (2282_2287 cm-1)(skyViewImaginaryRadiance2282_2287)
- Radiance standard deviation during hot blackbody view averaged over (675_680
cm-1)(HBBviewStdDevRadiance675_680) - Logical flag indicating that a data record is missing (true/false(missingDataFlag)
- AERI interferometer temperature at second port(interferometerSecondPortTemp)
- Time offset of tweaks from base_time(time_offset)
- Noise-equivalent Radiance in Hot Blackbody at 1000 cm-1(LW_HBB_NEN)
- Time (HHMMSS)(timeHHMMSS)
- Radiance standard deviation during ambient blackbody view averaged over
(2510_2515 cm-1)(ABBviewStdDevRadiance2510_2515) - Observation date(dateYYMMDD)
- Hot blackbody temperature - apex(HBBapexTemp)
- Julian Day including day and fraction of day(JulianDay)
- Ambient temperature used in calibration(calibrationAmbientTemp)
- Weight factor for bottom used in calculating hot blackbody temperature average(HBBbottomTempWeight)
- Scene mirror temperature as measured at the center of the back of the mirror(sceneMirrorTemp)
- Interferometer front end fan airflow unheated temperature: used with heated
temperature as measure of airflow.(frontEndFanAirUnheatedTemp) - Scene mirror motor case temperature(mirrorMotorTemp)
- Size of buffer holding initial spectrum(originalInterferogramSize)
- Radiance standard deviation during hot blackbody view averaged over (2282_2287
cm-1)(HBBviewStdDevRadiance2282_2287) - Field of view half angle used in finite FOV correction(FFOVhalfAngle)
- Difference between frontEndFanAirHeatedTemp and frontEndFanAirUnheatedTemp
indicative of front end air flow.(frontEndFanAirTempDiff) - Rain sensor analog output: the rain sensor is located inside the hatch near the
sky aperture and is used to flag the critical condition of rain falling on the AERI s(rainSensorIntensity) - Ambient blackbody temperature - rim top(ABBtopTemp)
- Limit applied to HBBtempDrift in determination of HBBstable flag(HBBtempDriftLimit)
- Stirling cycle cooler expander temperature(coolerExpanderTemp)
- Hot blackbody temperature - rim bottom(HBBbottomTemp)
- Signal conditioning electronics inside air temperature(SCEtemp)
- Type of scene that has been calibrated (ASCII character as float)(calibratedSceneID)
- Radiance standard deviation during ambient blackbody view averaged over (985_990
cm-1)(ABBviewStdDevRadiance985_990) - Stirling cycle cooler current(coolerCurrent)
- Resistive temperature of 12 Kohm fixed resistor located in SCE-P3 shell(fixed12KohmResistor)
- Imaginary radiance during sky view averaged over (985_990 cm-1)(skyViewImaginaryRadiance985_990)
- Longwave window brightness temperature from radiance average (985_990 cm-1)(longwaveWindowAirTemp985_990)
- AERI ingest computer temperature measured at back panel of computer(computerTemp)
- Ambient blackbody temperature(ABBbottomTemp)
- Observation longitude(Longitude)
- Blackbody controller Unit 1 power supply temperature(BBcontroller1temp)
- Resistive temperature of 2500 Ohm fixed resistor - banana plug mounted(fixed2500ohmResistor)
- AERI instrument unit serial number(AERIunitNumber)
- Radiance standard deviation during sky view averaged over (985_990 cm-1)(skyViewStdDevRadiance985_990)
- Observation latitude(Latitude)
- Duration of scene view(sceneViewDuration)
- Scene mirror motor driver heat sink temperature(motorDriverTemp)
- Radiance standard deviation during sky view averaged over (2510_2515 cm-1)(skyViewStdDevRadiance2510_2515)
- Size of buffer holding expanded spectrum before interpolation(expandedInterferogramSize)
- xxx(dataAvailable)
- Relative Humidity measured in the Interferometer Enclosure(interferometerEnclosureRelativeHumidity)
- Shortwave window brightness temperature from radiance average (2510_2515 cm-1)(shortwaveWindowAirTemp2510_2515)
- base time(base_time)
- Scene mirror position encoder value(sceneMirPosEncoder)
- Longwave radiance average (675-680 cm-1) Surface Air(surfaceLayerRadiance675_680)
- Logical flag indicating whether shortwave channel noise equivalent radiance is
acceptable in sky view (true/false). Determined using SWskyNEN and SWskyNENlimit.(SWskyNENacceptable) - Corrective offset for final hot blackbody average temperature(HBBtempOffset)
- Imaginary radiance during sky view averaged over (2295_2300 cm-1)(skyViewImaginaryRadiance2295_2300)
- Character string containing instrument name(instrumentUnitNumber)
- Radiance standard deviation during ambient blackbody view averaged over
(2295_2300 cm-1)(ABBviewStdDevRadiance2295_2300) - Time at center of AERI sky observation period(Time)
- Shortwave radiance average (2295_2300 cm-1) Surface Air(surfaceLayerRadiance2295_2300)
- The noise equivalent radiance observed in the longwave channel during a sky view
at 1000 cm-1(LWskyNEN) - Shortwave radiance average (2282_2287 cm-1) Elevated Air(elevatedLayerRadiance2282_2287)
- Hot blackbody temperature used in calibration(calibrationHBBtemp)
- Weight factor for bottom used in calculating ambient blackbody temperature
average(ABBbottomTempWeight) - Limit applied to LWskyNEN in determination of LWskyNENacceptable(LWskyNENlimit)
- Weight factor for top used in calculating ambient blackbody temperature average(ABBtopTempWeight)
- Stirling cooler compressor temperature measured at compressor heatsink(coolerCompressorTemp)
- Number of terms used in finite field of view correction(numberOfTerms)
- Radiance standard deviation during hot blackbody view averaged over (985_990
cm-1)(HBBviewStdDevRadiance985_990) - Number of complete (forward+backward) interferogram scans in sample average(coadditionsCount)
- Radiance standard deviation during sky view averaged over (675_680 cm-1)(skyViewStdDevRadiance675_680)
- Logical flag indicating whether HBB temperature is stable (true) or not stable
(false). Determined using HBBtempDrift and HBBtempDriftLimit.(HBBstable) - lat(lat)
- Characteristic value representing overall shortwave channel responsivity(SWresponsivity)
- Radiance standard deviation during hot blackbody view averaged over (2295_2300
cm-1)(HBBviewStdDevRadiance2295_2300) - Observation atmospheric pressure in AERI electronics(atmosphericPressure)
- Observation Altitude(Altitude)
- Ambient air temperature near the interferometer(airNearInterferometerTemp)
- Logical flag indicating whether hatch is open (true) or not open (false)(hatchOpen)
- Radiance standard deviation during ambient blackbody view averaged over
(2282_2287 cm-1)(ABBviewStdDevRadiance2282_2287) - Laser wavenumber used in definition of output wavenumber scale(outputLaserWavenumber)
- Radiance standard deviation during sky view averaged over (700_705 cm-1)(skyViewStdDevRadiance700_705)
- Blackbody controller Unit 2 power supply temperature(BBcontroller2temp)
- Weight factor for top used in calculating hot blackbody temperature average(HBBtopTempWeight)
- Shortwave surface air brightness temperature from radiance average (2295_2300
cm-1)(surfaceLayerAirTemp2295_2300) - Interferometer front end fan airflow heated temperature: used with unheated
temperature as measure of airflow.(frontEndFanAirHeatedTemp) - Maximum Temperature Difference Between HBB Thermistors(HBBmaxTempDiff)
- Version number of Operational Software(systemReleaseNumber)
- Number of views in a sequence(sceneMirPosCount)
- Motor step value given to motor controller to achieve proper mirror positioning(sceneMirrorMotorStep)
- Stirling cooler power supply temperature measured at power supply frame(coolerPowerSupplyTemp)
- The maximum excursion of hot-blackbody temperature over 5 consecutive scenes,
centered on the sky view(HBBtempDrift) - Interferometer window temperature measured on the outside of the aluminum window
flange(interferometerWindowTemp) - Shortwave window radiance average (2510_2515 cm-1)(shortwaveWindowRadiance2510_2515)
- Weight factor for apex used in calculating hot blackbody temperature average(HBBapexTempWeight)
- Imaginary radiance during sky view averaged over (675_680 cm-1)(skyViewImaginaryRadiance675_680)
- Maximum Standard Deviation in Thermistor Channels 0..7(maxSampleStdDev)
- Maximum Temperature Difference Between ABB Thermistors(ABBmaxTempDiff)
- Radiance standard deviation during hot blackbody view averaged over (2510_2515
cm-1)(HBBviewStdDevRadiance2510_2515) - Radiance standard deviation during ambient blackbody view averaged over (700_705
cm-1)(ABBviewStdDevRadiance700_705) - Characteristic value representing overall longwave channel responsivity(LWresponsivity)
- Longwave surface air brightness temperature from radiance average (675_680 cm-1)(surfaceLayerAirTemp675_680)
- Factor used to convert single-scan noise to two-minute equivalent(twoMinuteNoiseEstimateFactor)
- Imaginary radiance during sky view averaged over (700_705 cm-1)(skyViewImaginaryRadiance700_705)
- Detector temperature sensed via diode near detector(detectorTemp)
- AERI instrument data channel number(channelNumber)
- Radiance standard deviation during hot blackbody view averaged over (700_705
cm-1)(HBBviewStdDevRadiance700_705) - Logical flag indicating whether longwave channel noise equivalent radiance is
acceptable in sky view (true/false). Determined using LWskyNEN and LWskyNENlimit.(LWskyNENacceptable) - Radiance standard deviation during ambient blackbody view averaged over (675_680
cm-1)(ABBviewStdDevRadiance675_680) - BB Support Structure Temperature(BBsupportStructureTemp)
- Resistive temperature of 97 Kohm fixed resistor located in SCE-P4 shell(fixed97KohmResistor)
- Instrument scene mirror position identifier(sceneMirrorPosition)
- Weight factor for apex used in calculating ambient blackbody temperature average(ABBapexTempWeight)
- Noise-equivalent Radiance in Hot Blackbody at 2500 cm-1(SW_HBB_NEN)
- Shortwave elevated air brightness temperature from radiance average (2282_2287
cm-1)(elevatedLayerAirTemp2282_2287) - Maximum departure from ideal of the mirror position over the course of all
contributing views. Typically two hot, two ambient, and one scene view are examine(sceneMirPosEncoderMaxDrift) - Ambient air temperature at hatch opening(outsideAirTemp)
- Scene mirror view angle in non-negative degrees, measured clockwise looking into
interferometer window.(sceneMirrorAngle) - Original laser wavenumber assumed for this instrument(originalLaserWavenumber)
- Spare temperature sensor (location TBD)(spareTemp)
- Corrective offset for final ambient blackbody average temperature(ABBtempOffset)
- Ambient air temperature near blackbodies(airNearBBsTemp)
- Longwave window radiance average (985_990 cm-1)(longwaveWindowRadiance985_990)
- Electronics rack ambient temperature measured at inside top of rack(rackAmbientTemp)
- Radiance standard deviation during sky view averaged over (2282_2287 cm-1)(skyViewStdDevRadiance2282_2287)
- The noise equivalent radiance observed in the shortwave channel during a sky
view at 2500 cm-1(SWskyNEN) - Cold blackbody temperature used in calibration(calibrationCBBtemp)
- Dummy altitude for Zeb(alt)
- Imaginary radiance during sky view averaged over (2510_2515 cm-1)(skyViewImaginaryRadiance2510_2515)
- Relative humidity measured in the optics compartment atop the interferometer.(opticsCompartmentRelativeHumidity)
- Limit applied to SWskyNEN in determination of SWskyNENacceptable(SWskyNENlimit)
- Radiance standard deviation during sky view averaged over (2295_2300 cm-1)(skyViewStdDevRadiance2295_2300)
- Observation relative humidity at AERI blackbodies(atmosphericRelativeHumidity)
- Longwave elevated air brightness temperature from radiance average (700_705
cm-1)(elevatedLayerAirTemp700_705) - lon(lon)
- Longwave radiance average (700_705 cm-1) Elevated Air(elevatedLayerRadiance700_705)
- Ambient blackbody temperature - apex(ABBapexTemp)
- Blackbody cavity geometry factor(BBcavityFactor)
- Hot blackbody temperature - rim top(HBBtopTemp)
- Difference between actual and ideal motor encoder values for current view
indicative of quality of the mirror positioning.(sceneMirPosEncoderDrift)
sgpaeriB1.00: - null(Raw data stream - documentation not supported)
sgpaerich2B1.a1: - lon(lon)
- AERI instrument unit serial number(AERIunitNumber)
- Type of scene that has been calibrated (ASCII character as float)(calibratedSceneID)
- Time (HHMMSS)(timeHHMMSS)
- Observation longitude(Longitude)
- Mean of radiance spectra ensemble(mean_rad)
- Time at center of AERI sky observation period(Time)
- Character string containing instrument name(instrumentUnitNumber)
- Duration of scene view(sceneViewDuration)
- Ambient air temperature at hatch opening(outsideAirTemp)
- Observation latitude(Latitude)
- Maximum departure from ideal of the mirror position over the course of all
contributing views. Typically two hot, two ambient, and one scene view are examine(sceneMirPosEncoderMaxDrift) - Hot blackbody temperature used in calibration(calibrationHBBtemp)
- Observation relative humidity at AERI blackbodies(atmosphericRelativeHumidity)
- Logical flag indicating that a data record is missing (true/false(missingDataFlag)
- lat(lat)
- Wave number(wnum)
- BB Support Structure Temperature(BBsupportStructureTemp)
- wavenumbers for standard deviation of radiance spectra(wnum2)
- Logical flag indicating whether hatch is open (true) or not open (false)(hatchOpen)
- Time offset of tweaks from base_time(time_offset)
- Standard deviation of radiance spectra ensemble(standard_dev_mean_rad)
- base time(base_time)
- Version number of Operational Software(systemReleaseNumber)
- Observation date(dateYYMMDD)
- Ambient temperature used in calibration(calibrationAmbientTemp)
- AERI instrument data channel number(channelNumber)
- Scene mirror view angle in non-negative degrees, measured clockwise looking into
interferometer window.(sceneMirrorAngle) - Julian Day including day and fraction of day(JulianDay)
- Observation Altitude(Altitude)
- Dummy altitude for Zeb(alt)
- Observation atmospheric pressure in AERI electronics(atmosphericPressure)
- Cold blackbody temperature used in calibration(calibrationCBBtemp)
|