DQR ID | Subject | Data Streams Affected |
---|---|---|
D021113.6 | NSA/AERI/C1 - AERI extended range detector at Barrow | nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
D030203.1 | NSA/AERI/C1 - Failure of AERI cryogenic cooler | nsaaeriC1.00, nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
D030203.2 | NSA/AERI/C1 - Failure of AERI cryogenic cooler | nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
D050112.1 | NSA/C1 - Site-wide power failure | nsamplC1.a1, nsamwrpC1.b1, nsamplpsC1.a0, nsamwrlosC1.b1, nsamwrtipC1.a1, nsaaerich1C1.b1, nsaaerich2C1.b1, nsammcrmomC1.b1, nsamettwr4hC1.b1, nsavceil25kC1.b1, nsatwrcam40mC1.a1, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1, nsa915rwptempconC1.a1, nsa915rwptempmomC1.a0, nsa915rwpwindconC1.a1, nsa915rwpwindmomC1.a0, nsa915rwptempspecC1.a0, nsa915rwpwindspecC1.a0 |
D060331.1 | NSA/AERI/C1 - Excessive Noise in C1 AERI data | nsaaerich1C1.b1, nsaaerisummaryC1.b1 |
D060630.4 | NSA/AERI/C1 - Test data not representative of atmosphere | nsaaeriC1.00, nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerirawC1.00, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1, nsaaerilblcloudsC1.c1 |
D061020.2 | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
D070511.1 | NSA/AERI/C1 - Snow in enclosure | nsaaeriC1.00, nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
D071113.3 | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
D080322.1 | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
D110602.1 | NSA/AERI/C1 - Missing data | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1 |
Start Date | Start Time | End Date | End Time |
---|---|---|---|
04/18/2002 | 0132 | 05/16/2002 | 1830 |
Subject: | NSA/AERI/C1 - AERI extended range detector at Barrow |
DataStreams: | nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
Description: | The extended range detector had failed and a borrowed replacement detector was installed. The replacement detector had enough air present in the dewar to cause the cryogenic cooler to work at full current. The detector was still warmer than optimal and there is more noise present in the data than is considered normal. The data must be used with discretion. The system was shut off on 020516 due to noise and rising detector temperatures. |
Measurements: | nsaaerich2C1.a1:
nsaaerisummaryC1.a1:
nsaaerich1C1.a1:
nsaaeriengineerC1.a1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
01/20/2003 | 1835 | 01/25/2003 | 0041 |
Subject: | NSA/AERI/C1 - Failure of AERI cryogenic cooler |
DataStreams: | nsaaeriC1.00, nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
Description: | Failure of the cryogenic cooler for the AERI detector resulted in the instrument being shut down during the interval January 20, 2003 @1835GMT until January 25, 2003 @0041GMT, when a new cryogenic cooler was installed. All data are missing for this period. Data after the new cooler was installed are within normal acceptable limits. |
Measurements: | nsaaeriC1.00:
nsaaerich2C1.a1:
nsaaerisummaryC1.a1:
nsaaerich1C1.a1:
nsaaeriengineerC1.a1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
01/17/2003 | 1749 | 01/20/2003 | 1835 |
Subject: | NSA/AERI/C1 - Failure of AERI cryogenic cooler |
DataStreams: | nsaaerich1C1.a1, nsaaerich2C1.a1, nsaaerisummaryC1.a1, nsaaeriengineerC1.a1 |
Description: | In January 2003, the cryogenic cooler current for the Barrow, AERI detector was steadily increasing. This increase is a sign of cooler failure. On January 16,2003, the cooler began to make noise. The cooler was shut-off on January 17,2003 and any condensed gases were allowed to vent. Condensed gases in the detector dewar cause a cooler to work harder and increase the current. The cooler was then resealed and turned on. However, the cooler did not recover and the current was at a maximum. The cooler was unable to completely cool the detector and the detector never achieved a temperature below 72K. Higher detector temperature increases instrument noise. The instrument was shut off on January 20, 2003 at 1835GMT to prevent a catatrophic failure due to complete cooler failure and repressurization of the detector dewar, which would result in a subsequent implosion of the dewar. |
Measurements: | nsaaerich2C1.a1:
nsaaerisummaryC1.a1:
nsaaerich1C1.a1:
nsaaeriengineerC1.a1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
12/13/2004 | 1000 | 12/13/2004 | 2330 |
Subject: | NSA/C1 - Site-wide power failure |
DataStreams: | nsamplC1.a1, nsamwrpC1.b1, nsamplpsC1.a0, nsamwrlosC1.b1, nsamwrtipC1.a1, nsaaerich1C1.b1, nsaaerich2C1.b1, nsammcrmomC1.b1, nsamettwr4hC1.b1, nsavceil25kC1.b1, nsatwrcam40mC1.a1, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1, nsa915rwptempconC1.a1, nsa915rwptempmomC1.a0, nsa915rwpwindconC1.a1, nsa915rwpwindmomC1.a0, nsa915rwptempspecC1.a0, nsa915rwpwindspecC1.a0 |
Description: | The Barrow facility experienced a site-wide power failure on 12/13. Power was restored to most instruments between 2250 and 2330 GMT. |
Measurements: | nsa915rwpwindspecC1.a0:
nsa915rwpwindconC1.a1:
nsaaerich2C1.b1:
nsamwrlosC1.b1:
nsaaerisummaryC1.b1:
nsa915rwptempmomC1.a0:
nsaaerich1C1.b1:
nsamplpsC1.a0:
nsavceil25kC1.b1:
nsa915rwptempspecC1.a0:
nsa915rwptempconC1.a1:
nsaaeriengineerC1.b1:
nsamplC1.a1:
nsammcrmomC1.b1:
nsamettwr4hC1.b1:
nsamwrpC1.b1:
nsa915rwpwindmomC1.a0:
nsamwrtipC1.a1:
nsatwrcam40mC1.a1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
09/30/2005 | 0000 | 07/01/2006 | 2359 |
Subject: | NSA/AERI/C1 - Excessive Noise in C1 AERI data |
DataStreams: | nsaaerich1C1.b1, nsaaerisummaryC1.b1 |
Description: | Initially it was believed that the greater noise level in AERI C1 data was due to the extended range detector, which has lower sensitivity. However, when the S01 AERI was installed next to the C1 AERI and it stabilized on 9/30/2005, it was observed that the noise levels on the newly installed S01 AERI were much lower than for the C1 AERI. Therefore, the excessive noise of the C1 AERI is not due to the fundamental nature of the extended range detector but instead due to failure within the detector. The failure could be due to a poor D* value of too high a detector temperature. It could also be caused by optical alignment issues. In either case, the spectral radiance data have much more noise and that results in larger error bars when using the radiance data, especially long wave data as monitored by the LW_HBB_NEN flag. On 9/30/2005, the S01 AERI, which is next to the C1 AERI, came on-line and is producing low noise data. The S01 data should be used instead of the C1 data where low noise requirements are needed. On 6/26/2006, the S01 AERI went offline due to a laser failure. The C1 AERI was moved to the connex where data were within reasonable limits for an extended range detector. Beginning 20060701, the C1 data are the preferred AERI data set at the NSA Barrow location. |
Measurements: | nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
06/27/2006 | 0000 | 06/30/2006 | 1700 |
Subject: | NSA/AERI/C1 - Test data not representative of atmosphere |
DataStreams: | nsaaeriC1.00, nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerirawC1.00, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1, nsaaerilblcloudsC1.c1 |
Description: | The AERI had high levels of noise and testing was conducted to determine the cause of the noise. These tests occurred June 27 through June 30. Data collected during this time should not be used. It was collected to test the instrument and does not represent atmospheric data. The instrument was restarted in the connex using the upgraded Windows rapid sampling system on June 30, 2006 beginning 17:00 GMT. |
Measurements: | nsaaeriC1.00:
nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerirawC1.00:
nsaaerilblcloudsC1.c1:
nsaaerich1C1.b1:
nsaaeriengineerC1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
10/18/2006 | 0000 | 11/22/2006 | 2359 |
Subject: | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration |
DataStreams: | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
Description: | On 18 Oct 2006, a thermistor that measures the temperature of the blackbody support structure failed, resulting in erroneously high values. This measurement, which is captured by the field "BBsupportStructureTemp", provides the temperature of the radiance that is reflected into the blackbody (i.e., captured by the field "calibrationAmbientTemp"), and thus the calibrated radiance (the field "mean_rad") was incorrect and outside the ARM specification that the AERI data should be absolutely calibrated to within 1% of the ambient radiance. The broken thermistor was fixed on 22 Nov 2006. Fortunately, since the emissivity of the blackbodies is so high, absolute accuracy of the calibrationAmbientTemp is not required but should be within a few degrees. The radiance data have been recalibrated using the ambient blackbody temperature (the field "calibrationCBBtemp") as a surrogate of the calibrationAmbientTemp. Historically, the calibrationAmbientTemp and calibrationCBBtemp measurements have been within 1-2 deg. As a result of this recalibration, the radiance data are now absolutely calibrated to better than 1%. |
Measurements: | nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
04/17/2007 | 1800 | 04/18/2007 | 2359 |
Subject: | NSA/AERI/C1 - Snow in enclosure |
DataStreams: | nsaaeriC1.00, nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
Description: | A heavy, wet snowstorm late on April 17th and early on the 18th resulted in wet snow packing around the arms of the AERI's hatch controller. This resulted in the ventilator fan not shutting down when the hatch closed, and thus snow was packed into the front of the AERI (i.e., around the scene mirror and blackbodies). The data for this period should not be used. |
Measurements: | nsaaeriC1.00:
nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
11/01/2007 | 2246 | 11/28/2007 | 1930 |
Subject: | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration |
DataStreams: | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
Description: | On 11 Nov 2007, a thermistor that measures the temperature of the blackbody support structure failed, resulting in erroneously high values. This measurement, which is captured by the field "BBsupportStructureTemp", provides the temperature of the radiance that is reflected into the blackbody (i.e., captured by the field "calibrationAmbientTemp"), and thus the calibrated radiance (the field "mean_rad") was incorrect and outside the ARM specification that the AERI data should be absolutely calibrated to within 1% of the ambient radiance. The broken thermistor was fixed on 28 Nov 2007. Fortunately, since the emissivity of the blackbodies is so high, absolute accuracy of the calibrationAmbientTemp is not required but should be within a few degrees. The radiance data have been recalibrated using the ambient blackbody temperature (the field "calibrationCBBtemp") as a surrogate of the calibrationAmbientTemp. Historically, the calibrationAmbientTemp and calibrationCBBtemp measurements have been within 1-2 deg. As a result of this recalibration, the radiance data are now absolutely calibrated to better than 1%. The reprocessed data were archived 21 Jan 2008. |
Measurements: | nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
12/17/2007 | 0000 | 02/13/2008 | 2330 |
Subject: | NSA/AERI/C1 - Reprocessed: Failed temp sensor affected calibration |
DataStreams: | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1 |
Description: | The blackbody support structure temperature sensor on the NSA.C1 AERI were biased high by approximately 25K beginning 20071217 and became progressively worse until the sensor was replaced 20080213. The temperature from this sensor is used to calibrate the radiance data for the AERI. The AERI data have been reprocessed by replacing the data from the failed sensor with the cold blackbody temperature sensor data and producing corrected/recalibrated radiance data. The reprocessed data were archived in March 2008. |
Measurements: | nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
|
Start Date | Start Time | End Date | End Time |
---|---|---|---|
01/28/2004 | 2350 | 02/16/2004 | 0010 |
10/27/2004 | 2356 | 10/31/2004 | 0832 |
12/25/2004 | 2352 | 12/28/2004 | 0012 |
07/08/2005 | 2356 | 07/10/2005 | 0010 |
06/28/2006 | 2355 | 07/05/2006 | 0002 |
02/03/2007 | 2355 | 02/05/2007 | 1843 |
08/25/2010 | 2303 | 05/24/2011 | 0300 |
Subject: | NSA/AERI/C1 - Missing data |
DataStreams: | nsaaerich1C1.b1, nsaaerich2C1.b1, nsaaerisummaryC1.b1, nsaaeriengineerC1.b1 |
Description: | Data are missing and unrecoverable. |
Measurements: | nsaaerich2C1.b1:
nsaaerisummaryC1.b1:
nsaaerich1C1.b1:
nsaaeriengineerC1.b1:
|